We offer extra deep impact sockets with 3/8”, 1/2”, 3/4″ ,1”, 1-1/2”, and #5 spline drives. Prices below are listed as 12” or shorter. There is an additional charge for longer sockets.
How long is a deep socket?
Drive, 6″ Long.
What is deep socket?
Deep sockets (right image) can reach the nut on a longer, threaded bolt; they also allow you to reach recessed fasteners. 6-point sockets (left image) and 12-point sockets (right image) are available to fit a variety of fastener heads; universal sockets work with more fastener types, including spline, star and square.
What is the difference between a deep and shallow sockets?
deep sockets: Imagine a nut that, when fully tightened, sits an inch below the top of the bolt or stud it attaches to. A normal, shallow socket may not even touch the nut before the top of the stud or bolt hits the end of the socket.
Are there extra deep sockets?
Sunex 2851 1/2-Inch Drive 5-Inch Extra Long Deep Metric Impact Socket Set, 12 Piece.
Are all deep sockets the same length?
There are many different standards for sockets and whilst they are generally similar, they may set different tolerances, giving an acceptable range of lengths within the same standard. This means one manufacturer’s deep 13mm socket may be slightly longer or shorter than another’s.
Is a 6 point or 12 point socket better?
Answer: It’s true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners.
What are deep sockets good for?
Deep sockets: A deep socket can help you reach bolts that are far down in a vehicle or piece of machinery that you’re working on. These are often needed when the bolt protrudes from the nut, like a tire lug nut, or the fastener is recessed.
What is socket length pile?
The depth up-to which the RCC end bearing piles must be penetrated within the Hard Rock is known as the socket length. 10000+450 mm =10450 mm. The socket length in this case is 450mm. This is for proper grip in the rock.
What are deep well sockets used for?
Deep sockets are better for specific jobs instead of general use. If you have bolted joints, they make a much better option for your socket wrench than shallow sockets. If you need to replace your exhaust, you’d find it much easier to loosen the clamp bolts with a deep socket.
Article first time published on
Are Harbor Freight impact sockets good?
For a rough and tough set of sockets at a great deal the Harbor Freight sockets are a great buy. However we feel for a few bucks more you can get a much nicer set like the Tekton’s that include the laser etching and storage case.
How much torque can a 3/8 ratchet handle?
ACDelco 12V 3/8-Inch Cordless Ratchet Alone, it provides 45 pounds of torque—more than enough to snug a bolt initially—and users can then apply up to 100 pounds of torque by hand to tighten the bolt all the way.
What is the most commonly used and versatile socket handle?
A ratchet is the most commonly used and versatile socket handle. It can either loosen or tighten bolts. Pliers are used to grip, cut, crimp, hold, and bend various parts.
What is the most common socket drive size?
⅜-inch drive size sockets are the most common and most available.
Will a 12 point socket fit a square nut?
usually you can find a 12pt socket that will fit over a square nut, but thats not something they are designed for. if the nut is very tight, you will likely round it off.
What is a 12pt socket?
The additional points make these sockets easier to connect with the heads of fasteners. This is ideal if you are trying to work on a fastener that is hard to see or you cannot see at all. 12 point sockets are also great for use in tight spaces as they allow you to connect to a fastener at more angles.
What color are most impact sockets?
Impact sockets are typically black. This is because the surface is carbonized in order for it to harden. Ensuring that the surface is hard allows the sockets to absorb sudden torque changes i.e. “impact” a lot better.
How do I know what size socket I need?
- Turn on the digital caliper and set it to read in inches, not millimeters. …
- Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.
- Check the caliper display. …
- Turn on the digital caliper and set it to read in millimeters, not inches.
What is the smallest socket drive?
3/8″ Drive1/4″ Drive1/2″ Drive7mm5mm10mm8mm5.5mm11mm9mm6mm12mm10mm7mm13mm
What are socket sizes?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters).
Is code for piles in rock?
Geotechnical investigation data as laid down as per IS 1892, IS 13063 or any other relevant IS code. The rock profile, contours, the geological data and the necessary information as listed in IS 13063 along with the engineering and physical.
What is a bored pile?
Bored piles are cylindrical foundation elements made of concrete (with or without reinforcement), which are installed in the ground by a variety of methods. They transmit high structural loads into lower, load-bearing soils.
What are 8 point sockets used for?
What is an 8 point socket used for? Our range of 8 point sockets are perfect for use on our range of Pyramid Head Door Screws, Lag Bolts and Square Headed Machine Bolts. 8 point sockets take away the need for the use of a shifter and will stop you rounding off the head of a square bolt.
Will a 6 point socket work on a 12 point nut?
Both 6-point and 12-point sockets can be fitted on hex nuts, the primary differences being convenience and torque. … In other words, you would need to rotate only up to 30 degrees to fit a 12-point socket onto a hex nut. This can prove to be a time-saver and make life easier when you’re working within confined spaces.
What is the best steel for impact sockets?
What Is Chrome Molybdenum? Chrome molybdenum, also called Cr-Mo or chromoly, is a type of steel made from combining chromium, molybdenum, iron, and carbon alloy elements. It has stronger impact resistance, strength, and toughness than chrome vanadium, so it is typically used for tools like impact sockets.
Are impact sockets different than regular sockets?
The wall of an impact socket is around 50% thicker than that of a regular hand tool socket, making it suitable for use with pneumatic impact tools, whereas regular sockets should only be used on hand tools.
How much do sockets weigh?
Average Impact SocketLanj Socket InsertSocket Size ″Weight/2″3.222.452-1/8″3.592.202-1/4″3.881.91
What is the difference between metric and standard sockets?
Metric socket wrenches fit fasteners where that nominal length is a round number of millimeters (8mm, 10mm, 15mm). “Standard” (often “inch” or “SAE”) socket wrenches fit fasteners where that nominal length is a round fraction of an inch (1/4″, 1/2″, 13/16″).
Are Pittsburgh sockets good?
HF does carry some junk, but that is to be expected at a “discount store.” However, their Pittsburgh line of tools are actually pretty good, especially if you don’t work with tools every day, and just need some around the house for the occasional job.
Are impact sockets universal?
The 10 Piece Metric Impact Universal Socket Set offers a wide variety of sockets for any user need. These metric sockets have DirectTorque technology to help prevent rounding of fasteners and provide better grip.
Where are icon sockets made?
Icons sockets are made in Taiwan. Most people wonder where Icon tools are made. All the tools by Icon are made in Taiwan and they guarantee you quality. This brand is owned by Harbor Freights.
