How do I know if my petsafe transmitter is working

1. Using the Test Light, with the Static Correction Level set at 2 or greater, hold the Receiver Collar at your pet’s neck height with logo side facing away from the Transmitter. 2. Walk towards the Boundary Zone until the Receiver Collar beeps and the Test Light flashes.

Why is my petsafe collar not working?

If Receiver Collar does not beep and the Test Light does not flash, replace the 10. battery in the Receiver Collar. If it still does not beep and the Test Light does not flash, contact the Customer Care Center at 1-800-732-2677. If the Receiver Collar beeps, there may be a complete or partial break in the 11.

Why is my petsafe collar blinking red?

Charging too often can reduce battery life. Charge your receiver collar when the receiver indicator light blinks red. The system works by sending a radio signal through a buried wire (boundary wire). Your pet wears a receiver collar that picks up the signal.

Why does my petsafe wireless transmitter keeps beeping?

If your Invisible Fence control panel is beeping every second, the most likely issue is that you have a wire break somewhere on your property. … If your Invisible Fence control panel is beeping with a lengthy pause between each beep, it’s possible your backup battery unit needs to be replaced.

Why is my petsafe collar beeping but not shocking?

Touch both points on the collar while it is ticking or beeping. If you do not feel a shock, then there may be a problem with the receiver collar. Make sure you touch both points on the receiver at the same time when you hear the collar beeping. It will tell you definitively that the fence is or is not working.

How do you activate a bark collar?

Use a large coin to turn the battery clockwise until the arrow lines up with the lock symbol on the housing. This turns the Bark Control Collar on. To remove the battery, turn the battery counter- clockwise using a large coin. Removing the battery turns the Bark Control Collar off.

How do I turn on my PetSafe rechargeable bark collar?

Press and hold the power button (D) until you hear a low to high beep and the green LED appears, and then release. The green LED will flash once every 5 seconds. Press and hold the power button until the bark collar beeps high to low, and then release.

How do you reset an invisible fence transmitter?

Some models have a battery-operated fence component that helps with the signal transmission. Plug in the transmitter. The system and transmitter should reset automatically upon being plugged back in. Wait for a few seconds and look for any abnormality in the lights.

How do I reset my petsafe wireless collar?

Make sure the collar is powered on. Press and hold the button on the collar until a beep is heard and the light flashes green to turn the collar on. Press and hold the power button for 10 seconds to reset the collar. The light turns red and the collar turns off.

What does blinking green light mean on Invisible fence?

When you first insert the battery into your receiver, the status light will flash green. This indicates that the receiver has started properly. In the event that the lights do not flash, check the battery to be sure that it has been inserted properly.

Article first time published on

How do you put a collar on petsafe Wireless stay and play?

Set Up Your Collar Press and hold the button until the light flashes red. The number of flashes on the collar indicates the current collar level. Press again quickly to increase the collar level. To set lower levels, continue through all the levels until you see one flash indicating level 1.

How do I program my invisible fence collar?

The collar will beep or blink in series to indicate the new shock level. Press the button again within 5 seconds to raise the level once more. Continue until the collar indicates it is at the correction level you desire. To lower the correction level, continue pressing the button; the level will cycle back to 1.

How do you test a petsafe rechargeable bark collar?

Press and release the power button to power the collar on.
Watch for the green light to blink twice, then hold the power button. Continue to hold the power button through the red light.
Release the button when the light turns blue to set the collar into test mode.

Why is my dog's bark collar not working?

Make sure the collar is properly placed high on your dog’s neck close to the ears with the contact points touching the center of your dog’s neck. Tighten the NoBark and make sure the contact points touch his skin. … If your dog still does not respond, contact the Customer Care Center at 1-800-732-0144.