Resetting a Rain Bird ESP-Me is easy. To reset the irrigation controller, all you need to do is turn the dial to ‘Seasonal Adjust’ then hold the left and right buttons down until the LCD display says ‘CLEARED’ then your ESP-Me irrigation controller has been reset.
How do you program Rainbird cycle and soak?
So rather than watering for 24 minutes straight, your controller will “Cycle” for 8 minutes, wait 52 minutes for the water to “Soak” in, Cycle for another 8 minutes, wait 52 minutes for the water to soak in again, and then finally water for a final 8 minutes, for a total of 24 minutes.
Why is my Rainbird not working?
Circuit breaker/fuse – Check the condition of the circuit breaker or fuse, if it has been blown the most likely reason is a field wiring short. An Electromechanical controller will stop on the station that caused the problem. Reset the controller to its rest position and replace the fuse or reset the circuit breaker.
What is the Rainbird controller password?
The controller password is restricted to letters and numbers, 4-8 digits in length. No special characters. If you use a special character it will not be registered in the password. As an example, if you typed in [email protected], the password would be stored as 1234.
How many minutes should each sprinkler zone run?
Water Thoroughly: Rotor zones should run for about 30-40 minutes per zone and spray zones 10-15 minutes per zone.
How long should I run my Rainbird sprinkler system?
Keep It Balanced. Put measuring cups in various places around your lawn and run the sprinklers for 15 minutes. This will give you an idea of how much water the grass is getting and where. You’re looking for about one to two inches—depending on the soil—evenly distributed.
How many minutes should I water my lawn?
It is ideal to water lawns about one inch of water per week. To determine how long you need to water to get one inch, place a plastic container in your yard and set a timer. On average, it will take 30 minutes to get a half inch of water. So, 20 minutes, three times per week will give a lawn about an inch of water.
What is cycle soak Rainbird?
The best way to water your lawn is to use the “cycle and soak” method. This method breaks up your watering time into smaller cycles, allowing the water to soak into the soil.
What does cycle and soak mean on Rain Bird?
Cycle+Soak is an exclusive feature in Rain Bird Central Control software that allows users to precisely schedule and apply water to be consistent with the infiltration rate of the soil in each specific area around the golf course.
How do you program a cycle and soak?
To program your controller for Cycle and Soak, simply take the total time for each zone and divide it into multiple cycles. For example, instead of watering a single zone for 15 minutes, set your sprinklers to water three times at 5 minutes. As a general rule, 30 minutes is all you need to wait between cycles.
Article first time published on
How do I connect Rainbird to alarm com?
To add the Rain Bird Controller to an Alarm.com account: On a mobile device, log into the Rain Bird app. Select the Controller, then tap the Settings icon. Tap to expand Connected Home , then tap the toggle switch next to Alarm.com . Return to the home page of the Rain Bird app.
Where do I find Rainbird controller password?
Press on “Controller Info” down arrow and enter a new password. The controller password is restricted to letters and numbers, 4-8 digits in length. No special characters. Don’t forget to press “Done” at the top right once the password is entered.
What is rain Sim password?
The router software home page will display, the username is admin and the password is admin.
What should I set my rain sensor to?
IFAS researchers recommend rain sensor thresholds of 1/4” for 2 or 3 day per week irrigation with no more than 1/2” for 1 day per week irrigation. Remember, the lower the setting, the more water saved.
How do you reset a Rainbird sprinkler system?
Press and hold the left and right arrow buttons at the same time for at least 3 seconds. Until you see the word “CLEARED” on the screen. Your ESP-Me is now restored to the factory default settings.
How do I turn on my Rainbird sprinkler system after winter?
- Turn on the main water supply for the sprinkler system. …
- Open the ball or gate valve all the way once you hear the water rushing through the pipe.
- Press the “Manual” start button on the Rainbird controller.
Should solenoid be on or off?
Avoid over-turning the solenoid in either direction, as this can cause damage to the components or cause pressurised water to escape the solenoid. When you hear water rush through the device, it’s easy to tell that the valve has opened successfully.
How does the water timer work?
A mechanical timer hooks directly to your faucet and works just like an egg timer in your kitchen — you twist the dial to whatever water duration you want and your faucet will shut off automatically when the timer is finished. Mechanical timers are great for a few reasons: More convenient than hand watering.
How do rotating sprinklers work?
The sprinkler head pivots on a bearing on top of its threaded attachment nut. The head is driven in a circular motion by the force of the outgoing water, and at least one arm extends from the head. The sprinkler arm is repeatedly pushed back into the water stream by a spring.
