The hot tub high limit switch is sometimes triggered when you’re refilling your hot tub and can be reset by pressing the large red button on your spa pack.
Why does my hot tub keep saying HL?
An HL error usually means there is a blockage, preventing water from circulating around the pump & heating system.
How do you test a hot tub high limit sensor?
- Shut off all power to the spa at the breaker and spa pack.
- Set your Ohm meter to the 20K setting.
- Locate the wire ends and remove the plug from the board.
- Place your meter leads onto the green and red wire.
- Compare readings to Thermistor Resistance vs. Temperature Chart.
How do I fix high limit hot tub?
Switch Reset Sometimes, your switch just needs a good reset. On your spa pack you will find a red button that will reset the high limit switch. Once you reset it, test your hot tub to see if it trips again. If it doesn’t, the reset did the trick.
Where is the high limit reset button?
The High Limit Reset Button is located behind the gas valve.
How do you reset aqua spa?
- Locate the spa’s high-limit reset. This is a red button found on many spa packs. …
- Press the high-limit reset button. …
- Turn on your spa and observe its operation. …
- Flip the breaker panel switch on or press the reset button on the GFCI outlet to restore power.
How do I know if my high limit switch is bad?
One of the most common issues that happens when a high limit switch goes bad is that it fails to signal the blower fan to turn off. If your fan keeps running continuously (and you’ve checked that your thermostat is set to AUTO rather than ON), that could be a sign of a bad high limit switch.
Why doesn't my hot tub heat up?
If your spa heater won’t heat, remove and clean the filter(s) to rule out a pressure or flow rate problem in your hot tub heater. Low water level, a clogged pump impeller, closed valves, clogged pipes, or blocked spa drain covers can also cause flow issues.
Why is my inflatable hot tub not heating up?
If your hot tub won’t heat the water properly, it could be the heater element or low flow from your pump. Most heating failure result from corrosion caused by low PH in water supply. Any PH below 7.0 damages the heating element and trips the GFCI breaker.
How do you reset a high limit switch on a furnace?
- Locate your furnace’s heating duct. …
- Locate the white limit switch. …
- Look at each arm to identify the settings. …
- Identify the component (setting) located in between the two arms. …
- Set the temperature on the middle component to approximately 105 to 115 degrees Fahrenheit.
Article first time published on
What is high limit switch?
The high temperature limit switch (also known as a furnace plenum thermostat) is a safety device on a furnace that is designed to cut the gas supply when the burner temperature exceeds the safe operating range. When the temperature drops back within the safe range, it will allow the gas valve to open again.
Why is my hot tub red light flashing?
When the power indicator is FLASHING RED, this means that the heater high limit has tripped. This means that the tub could be above its temperature limit or that the filters are clogged. The red flashing lights usually means that you’ll need to call for service.
What does a high limit switch do on a pool heater?
HIGH LIMIT SWITCH – These switches monitor water temperature in the header. If the temperature exceeds a set limit, either switch will shut off the heater.
Where is the temperature sensor on my hot tub?
On most hot tubs, this sensor is located just inside of the filter housing. The temperature probe should be pushed down securely into the thermowell, and the capillary should not have any kinks.
How do you adjust a pressure switch on a hot tub?
Some adjustable pressure switches have an Adjustment Screw of grey plastic that accepts a small skinny flathead. Turn the screw slowly to the left, counter-clockwise, to reduce the minimum required pressure. Turn it slowly just barely beyond the point where the heater turns On.
How do you reset the heater on a Hot Springs spa?
Disconnect the power source from the spa. Wait 30 seconds and reset the heater high limit. The reset button is located in the equipment compartment. Plug the spa back into the power source.
Why is my hot tub getting too hot?
A simple cause of hot tub overheating is the hot tub’s temperature may be set too high. … So, if the hot tub is set to filter too many hours per day, it can cause overheating. Adjust your filter cycle duration cycle down and set it to run early AM and late PM, when the outside temperatures are coolest.
How do you bypass a hot tub flow switch?
Use another short piece of wire to connect the two wires you just pulled off that connect the spa to the main control panel. This action bypasses the flow switch and completes the electrical circuit back to the main control panel.
Is there a reset button on a hot tub pump?
There are generally two “hard resets” in hot tubs, the GFCI, and the high limit reset. The GFCI pops if there is any type of electrical short (such as water getting into the heating element, the reset on that can be in one of three places.
How do I fix the HL code on my Arctic Spa?
Turn the power off at the breaker for 15 seconds and then flip it back on. This will reset the HL reading. You will notice the display show some numbers. This is just the software version.
Why won't my lazy spa heat up?
Unplug the pump from the socket. Whilst the pump is unplugged press the thermal reset button in and hold for 5 seconds. Plug the pump back in to the socket. Set the pump to heat and allow for 5-6 hours of heating.
How do I know if my heating element is bad in my hot tub?
To test if a bad heater is causing your tripped breaker, you can disconnect the copper tabs (or wires) from the spa pack to the heater element. Once disconnected, turn the power back on. If the breaker stays on, you‘ve determined that the heater is bad. Find a replacement heater element.
Does hot tub heat up faster with jets on?
A hot tub heats up faster if the jets are turned on. This is because the water circulates with the jets on, which evenly disperses heat and prevents cold water from being trapped in the hot tub pipes.
What causes a high limit switch to trip?
If the air inside your furnace gets too hot, the limit switch trips to prevent overheating. If the furnace high limit switch trips due to overheating, there is likely an airflow issue that is preventing proper air movement through the system. … A dirty filter is the most common cause of airflow issues.
Why is my furnace going off on high limit?
In a gas furnace, a high-limit, switch turns the unit off if air doesn’t ventilate from the exhaust flue properly. … A high-limit switch will turn a furnace off if it becomes too hot or is obstructed. Changing the furnace’s air filter and cleaning the blower motor may help the switch perform better.
Where is furnace reset button?
Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.
How does a high limit thermostat work?
Anytime you have an element that heats, safety dictates you have a way to stop the appliance from overheating in case the temperature-regulating controls fail. That’s what the high-limit thermostat does: It shuts off the heating element if the water reaches an upper temperature limit, usually about 200 degrees.
What safety function does the limit switch perform?
What safety function does the limit switch perform? It prevents the furnace from overheating.
Why is my Sundance hot tub light red?
The indicator light located on the front cabinet panel of the spa is an early detection system that will notify you when the spa needs immediate attention. A solid white light indicates that all operations are normal. A solid red light indicates that immediate attention is required to clear or fix an error code.
How do I test my hot tub control panel?
If the problem persists, turn the breaker off and disconnect the panel to examine the circuit board. Turn the power on and check if the hot tub heats up or starts to filter. The surest way to check if a control panel works is to use one you know is working and connect it to the circuit board.
How does swimming pool heater work?
An electric heater for your pool draws outside air in and circulates this air through an outer evaporator air coil. The liquid refrigerant within the evaporator coil absorbs the heat from the outside air and transforms it into a gas. The warm gas in the coil passes through the compressor where heat is increased.
