Hold down the arrow (>) button for 2 seconds. … This feature automatically defaults to program A. … The station number will be flashing. … Press the arrow (>) button scroll to the station you wish to begin with.
Why does my X-core sprinkler not work?
If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down. … If the sprinklers do not turn on you may have a valve shut down that supplies the irrigation system.
How do I set the time on my hunter node?
To set the time and date on the node press the center button, simply scroll through the choices using the left and right arrow buttons and adjust the displayed item using the plus and minus buttons. Push the button until the icon is displayed. All 4 digits will be displayed representing the year.
How do I manually turn on Hunter nodes?
- To manually activate a program, press and hold the right arrow button until the. icon is displayed, then quickly press the PRG button. …
- To stop the Manual watering cycle press the minus button until the time is reduced to zero.
- Press the.
Why won't my hunter sprinkler system come on?
If the sprinklers do not turn on you may have a valve shut down that supplies the irrigation system. … Check the wiring connections at the valves for loose or corroded connections. If you do not have a master valve, then check the common wire connections at the irrigation valves for loose or corroded connections.
How do I start my sprinkler system?
Slowly open the main shutoff valve to let water into the sprinkler system. For a ball valve, turn the lever handle one-quarter turn until the handle is parallel to the pipe; this is the fully open position. For an in-ground shutoff valve, use a sprinkler valve key to turn the valve counterclockwise until it stops.
How do I reset my automatic sprinkler system?
- Turn the control dial to the “off” position.
- Press the “next” button to access the clear-memory feature. …
- Press and hold the “off” button until the display stops blinking.
- Turn the control dial to the “run” position.
- Press and hold down the “minus” arrow and “prog” buttons simultaneously.
How do I turn on my orbit sprinkler head?
Pop Up Orbit Sprinkler Use a pull up tool to lift up the metal screw on the center of the nozzle. With the screw loose, the sleeve can be turned clockwise until it comes off. At the same time, turn the nozzle counterclockwise. You can choose how far you want to turn it.
How do you manually turn on orbit sprinkler valves?
To open the valve manually, twist the manual bleed screw counter-clockwise until the valve opens. It usually doesn’t need to be more than one-half turn. To close the valve turn the manual bleed screw clockwise until the valve closes.
How does an irrigation controller work?
The stations send electrical impulses to their respective valves to open or shut them, letting water through to the sprinklers (or not). Because this works electronically, the controller has to be physically located near enough to the valves to allow for a wired hookup.
Article first time published on
What does the umbrella mean on Hunter node?
The display will show the umbrella icon flashing and On. Press the minus (-) button to bypass the sensor. … The icon will show on the display during normal operation, indicating the controller is in bypass mode. To reactivate the weather sensor press and hold the left arrow (<) button until the icon is displayed.
How do I reset my Hunter SRC Plus sprinkler?
- Press and hold down the , and buttons.
- Press and release the RESET button in the lower wiring compartment.
- Release the , and buttons. The display should now show 12:00a. m.
- All the memory has been cleared and the controller may now be reprogrammed.
What is SVC battery?
The SVC was Hunter’s original battery-powered controller. It was sunset in 2011 to make way for the Node, which offers longer battery life and expanded station options for various valve applications.
How do you reset Hunter X2?
- Turn the dial to the RUN position. …
- Press and hold the program button.
- Press and release the RESET button located inside the lower wiring compartment. …
- When the display reads the controller station count; (e.g. 14) then DONE, release the PRG button.
How do you test a hunter node?
Make sure the controller is in Idle Mode. Press and hold the PRG button until the icon is displayed. The station number will be displayed in the lower left side of the display along with the run time. Quickly press the plus or minus buttons to set the duration of watering time for the test program.
Why won't my sprinkler system turn on manually?
If your sprinkler system won’t turn on or if you have low water pressure, this could be caused by the valves not being turned on all the way. Just locate the valves and make sure they are both turned on (you should have 2 valves, one located on the horizontal pipes and one for the vertical ones).
