How do you adjust the idle on a Husqvarna chainsaw

L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning. Next, begin to slowly turn the adjustment screw counterclockwise until you hear the engine idling smoothly.

How do you adjust the idle screw on a Husqvarna chainsaw?

L Screw – With the chainsaw still running, take a screwdriver and turn the L screw clockwise. Keep turning it until the engine almost stops turning. Next, begin to slowly turn the adjustment screw counterclockwise until you hear the engine idling smoothly.

Why is my chainsaw idling high?

The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. … Adjust the screw to restrict fuel delivery by turning it clockwise with a screwdriver until the chain stops turning. The saw must be running when you do this.

Where is the idle adjustment on a Husqvarna chainsaw?

Locate the idle-speed screw and the idle-mixture screws on the side of the chainsaw. …
Turn both the low- and high-speed screws clockwise to the midpoint. …
Adjust the low-idle screw clockwise and counterclockwise respectively, until you find the highest idling speed.

Where is the idle screw on a chainsaw?

The LA setting on Stihl chainsaws is controlled by a screw on the outer housing of the engine that adjusts the flow of fuel and air through the carburetor. This screw is inside the engine housing on the carburetor, but is accessible through a hole or gap in the outer housing of the saw.

Why is my chainsaw revving on its own?

If your chainsaw is over-revving, it indicates a lean air-fuel mixture is supplied to the engine. The carburetor might need tuning, or there might be an air leak behind this. Clean the air filter and adjust your carburetor’s screws that control the amount of fuel in the fuel mix.

Why does my Husqvarna chainsaw stall?

A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.

What does H and L mean on a chainsaw?

They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet).

How does the idle adjustment screw work?

Once the air fuel mixture screws have been properly adjusted, and the engine runs smoothly both at idle, and when revved, it is time to locate the idle mixture screw. The idle mixture screw controls the air fuel mixture at idle speed, and often is located near the throttle plate.

Why is my chainsaw getting too much fuel?

The air filter may be clogged or dirty. If the air filter is clogged, the engine will get too much fuel and not enough air. … If the air filter is clogged, replace it or clean it.

Article first time published on

How do I know if my chainsaw is running rich?

Running too rich will usually smoke and lack power, it will foul up spark plugs and smoke you out, but it shouldn’t kill the saw. If it’s running well and sounds like it allways has go with the “it’s not broken… ” theory. If it doesn’t seem right, stop using it and check / adjust it ( or get the shop to ).

Why does my Husqvarna chainsaw dies at full throttle?

If your chainsaw engine dies at full throttle, check the following parts: the carburetor, fuel lines, fuel filter, air filter, and muffler. … When the carb becomes clogged (which is often the result of old fuel sitting in it over a long period of time, like over the winter), it will not perform this task effectively.

How do I keep my chainsaw running?

Keep your Chain Sharp: Keeping your chain sharp is probably the easiest and most effective way to extend the life of your saw. …
Flip your Bar: …
Drain your Gas: …
Check your Sprocket: …
Keep a watchful Eye:

How do I adjust idle speed?

Turn the idle screw, now exposed from the protective rubber coating, in order to adjust the idle. Loosen the screw in a counter-clockwise fashion to increase idle speed or tighten it in a clockwise manner in order to decrease the idle speed.

What is a chain brake on a chainsaw?

The chain brake is activated when the front hand guard, located near the saw’s upper handle, moves rapidly toward the chainsaw operator. When engaged, the chain brake stops the chain from rotating around the saw’s guide bar.

What does a clutch do on a chainsaw?

The clutch allows the engine to turn freely at low rpm [rpm=revolutions (turns) per minute] without moving the chain. They are separate. Unlike a four wheeler or truck, the chainsaw operator doesn’t have to engage the clutch or put the chainsaw in gear.

How do you adjust the carburetor on a Husqvarna chainsaw?

Method for Adjusting the Carburetor Start the saw and adjust the L screw by turning it clockwise until the engine almost stops. Turn it counterclockwise until the engine starts running smoothly and then check the adjustment by squeezing the throttle trigger and noting a smooth acceleration of the engine as you do this.

Why is my idle screw not working?

It is either a linkage problem or the butterfly plate is physically stuck. If the choke high idle adjuster and the throttle positioner (if you have one) adjuster screws are not the problem, it is time to remove the carb and check the linkage and butterflies to make sure that they shut properly.

Where is the idle screw on a carburetor?

The idle speed screw (arrow 1) is located on the primary linkage. The idle metering adjustment screws (arrow 2) are located on the primary metering block on most Holley carburetors. A typical starting location for these idle mixture screws is between 1 and 1 ½ turns out from fully seated.

What does the pilot screw adjust?

An air screw adjusts how much air is being delivered thru the pilot circuit: in is rich (less air) and out is lean (more air). A fuel screw adjust how much fuel (or air/fuel mixture) is being delivered from the pilot circuit. In is lean (less fuel) and out is rich (more fuel).

What does LA on a carburetor mean?

There are three of them, marked “H,” “L” and “I” or “LA,” depending on the model. They are the high-speed, low-speed and idle adjustments respectively. Determine the carburetor type before adjusting the high- and low-speed screws.