Completely drain tank by unscrewing drain cap at base of filter tank. Leave cap off during winter.Depress Vari-Flo control valve handle and rotate so as to set pointer on valve top between any two positions. This will allow water to drain from the valve.
How do I drain my Hayward pool filter for winter?
- Completely drain tank by unscrewing drain cap at base of filter tank. Leave cap off during winter.
- Depress Vari-Flo control valve handle and rotate so as to set pointer on valve top between any two positions. This will allow water to drain from the valve.
Where are pool drain plugs?
plug without an O-ring. Pool pumps usually have two pump drain plugs: one in the front, at the base of the hair and lint strainer or pump pot, and another plug further back toward the motor to drain the volute, or impeller housing.
Where is the drain plug on my pool pump?
Pool Heaters typically have 2 plugs, a drain plug in the front header and the rear header. Heat pumps usually have a small plug on the lower exiting pipe, but sometimes not, many are drained at the unions.
How do you open the drain on a pool filter?
Locate and remove the drain plug to begin draining the filter tank. Make sure to open the air relief on the top of your filter as this will help speed up the draining process. Once the tank has finished draining, locate the clamp and begin to loosen the nut using a wrench.
Where is the pool main drain valve?
The main drains are usually located on the lowest point in the pool, so the entire pool surface slants toward them. Most of the dirt and debris that sinks exits the pool through these drains.
What size is the drain plug on a Hayward pool pump?
Hayward Pump 1/4 Inch Drain Plug & Gasket SPX1700FG. Hayward Pump 1/4″ Drain Plug & Gasket fits all models of Hayward pumps.
Can I leave pool filter outside for winter?
If you store your filter in a shed or a detached Garage make sure you cover your filter and keep it away from chlorine or any corrosive chemicals that off gas. Sand filters should be left outside.
How do I drain my pool filter for the winter?
After a backwash and rinse, place the valve to the “winterize” setting on the top mount valve. This will allow water to drain from the valve. Next, you’re going to have to completely drain all the water from the filter tank. To do this simply unscrew and remove the drain cap on the bottom of the filter barrel.
How do you drain an above ground pool without flooding the yard?
- Unroll the pump’s intake hose so that it reaches the center of the pool (or as close to it as possible), and submerge it in the pool.
- Place the outlet hose so the exiting water doesn’t flood the area, but drains off away from the pool.
- Dry your hands thoroughly.
Article first time published on
How do you clean a Hayward cartridge?
You local Hayward dealer should have a cartridge cleaner or you can use a mixture of laundry detergent and water. 1-cup detergent to 5 gallons of water. Dissolve the detergent in a bucket of water and soak the element(s) for 24 hours. YOU MUST THOROUGHLY RINSE THE ELEMENTS PRIOR TO REINSTALLING THEM INTO THE FILTER.
How do you remove a lock ring from a Hayward xstream cartridge filter?
Depress safety latches (located on the underside of the locking ring handles) and unscrew locking ring in a counter-clockwise direction. Remove lid from filter body.
What does drain at bottom of pool do?
Main Drain: The main drain is typically located at the deepest point of the pool and is used to lower the water level, however its primary purpose is to circulate water from the bottom of the pool.
How do you drain a pool drain plug?
Shut off the pump. Go to the back of the filter and unscrew the drain plug. Turn the pump back on and let the water run until it reaches the point where you want to drain the water out. Turn the pump back off and put the plug back into the drain plug.
How long does it take to drain pool filter?
How long it will take to drain your pool will depend on the size of your pool, and how many gallons per minute the pump can move. But you’re probably looking at somewhere between 8 and 14 hours for your pool to empty.
How can you tell if a water valve is open or closed?
If the handle on top is parallel to the valve, it’s open. Likewise, if the handle is perpendicular to the top, the valve is closed. Common places you might find a ball valve are in irrigation and in sites where you need to control water supply from one area to another.
Is it bad to drain a pool?
First, if the draining is done at the wrong time or under the wrong conditions, you can actually risk damaging your pool structure and liner. All the water from your pool needs to go somewhere when it’s drained, and that usually means the ground. … For fiberglass pools, the risks of damage are even greater.
