Remove the strike plate from your door frame and use the deadbolt strike supplied with your Schlage lock
What is a Deadlatch lock?
A deadlatch is a type of lock that can automatically lock itself without needing a key or a knob to move the blot in place. Essentially, it contains its own security latch which can immediately lock itself as soon as you close your door. … A key must be used to unlock the door from the inside.
What is the backset on a door latch?
The backset is the distance from the edge of the door to the spindle mechanism on the latch. Usually for a 63mm case measurement it will have a 44mm backset and for a 76mm case measurement will have a 65mm backset.
Are all deadbolts adjustable?
Most deadbolt locks have an adjustable sleeve to accommodate the two typical backsets found on exterior doors drilled by the manufacturers. Failure to adjust the backset results in a lock that does not operate properly or at all.
How do you deepen a deadbolt?
Using the appropriate-sized spade bit and an electric drill, cut the hole in the door frame about 1/4 inch deeper. Test the latch mechanism again. If the twist knob stops in the same position with the door opened and closed, the hole is deep enough. If not, use the drill to make the hole another 1/4 inch deeper.
How do you enlarge a strike plate hole?
You can move the strike plate up or down and in or out. Use a sharp chisel to enlarge the strike plate mortise. Then hold the strike plate in place and drill new 1/16-in. holes for the screws.
How far apart should deadbolt and door knob?
The distance between a deadbolt and door knob is usually 5 1/2 to 6 inches above the handle. Most do not recommend placing it any higher than 6 inches from the original knob unless the situation calls for it.
What is the difference between a deadlock and a Deadlatch?
While a deadlock either needs a key to lock the door, or to turn a knob to move the bolt into lock mode. A deadlatch will automatically lock itself whenever the door is closed. This makes leaving the house quicker and you can be safe knowing the door is locked behind you.
Are there different size deadbolts?
Even though there is a standard size for deadbolts, you might need smaller or larger sizes depending on the size and thickness of your door. Different brands have deadbolt sizes as small as 2 inches and as big as 5 inches.
What is the difference between a Deadlatch and a spring latch?
A deadlatch is not spring-loaded, and provides extra security over a spring latch. … A latch is operated with a key on the outside and a turn-style knob on the inside. One great feature of a latch is that it can be set to automatically lock when the door closes.
Article first time published on
Why are there two pieces to a door latch?
To keep the latch bolt from being push-retractable once the door is closed, a second mechanism is incorporated into the latching mechanism—called a deadlocking plunger (the entire mechanism sometimes called a deadlock latch), as shown in Figure 3. … Dealocking plunger mechanism keeps latch bolt in place.
What is a backset on a door?
The backset is the distance from the edge of the door to the center of the 2-1/8-inch bore hole. In the United States, there are two common backsets for residential door locks: 2 3/8 inches and 2 3/4 inches.
How does a deadbolt mechanism work?
How does a deadbolt lock work? Because deadbolt locks operate without the use of a spring, simply turning a key retracts or extends the bolt into the strike plate on the door frame. … Thanks to the strong locking mechanism, deadbolts offer an extra layer of resistance and strength compared to other locking mechanisms.
What are the parts of a deadbolt lock?
- Thumb-latch / Thumbturn. The thumb-latch (or thumbturn) is the part of your deadbolt inside your home that you use to lock and unlock your deadbolt.
- Deadbolt. The deadbolt is the piece of the lock that secures your door shut.
- Turnpiece / Tailpiece. …
- Keyhole.
What does 40mm backset mean?
‘Backset’ is the distance from the front of the lock to the centre of the spindle as shown here. … Almost ALL domestic mortice locks and tubular latches are supplied with either a 44mm or 57mm backset length.
How do you measure night latch?
The size of a Night Latch is measured from the centre of the keyhole to the edge of the door where the night latch should finish.
What is backset size on a lock?
The backset is the horizontal distance from the edge of a door to the centre of a lockset; thus, the distance a lockset is ‘set back’ from the edge of a door is called its backset. It’s usually 1 inches or 2 inches (or 44mm and 57mm).
How do you move a strike plate on a door?
To snug the door up you would move the strike plate toward the center of the door jamb. Move it away from the center if the strike will not seat when the door is closed. For minor adjustments, you may be able to loosen the plate and tap it in the direction you need. Use a screwdriver to loosen the screws slightly.
What is deadbolt strike height?
According to ANSI specifications for cylindrical or mortise locks: … The lock strike centerline should be 40 5/16″ from the bottom of the frame with the lock in relation to the strike. The deadbolt strike centerline should be 48″ from the bottom of the frame.
What size hole do you need for a deadbolt?
Be sure to use the correct size drill bits specified in the lock set instructions, though most standard deadbolts require a 2 1/8-inch hole saw for the lock bodies and a 1-inch spade bit for the sliding bolt assembly.
What is the maximum height of a deadbolt lock in a door?
Door handles, pulls, latches, locks and other operating devices shall be installed 34 inches (864 mm) minimum and 48 inches (1219 mm) maximum above the finished floor. Locks used only for security purposes and not used for normal operation are permitted at any height.
