Begin by cutting the paper to size. Decide what size you would like your pendant to be and begin cutting several squares or rectangles of colored paper to that size. … Add more layers of paper. … Make each layer smaller than the last. … Allow the glue to dry. … Sand the edges. … Finish the jewelry.
How do you make layered paper jewelry?
- Begin by cutting the paper to size. Decide what size you would like your pendant to be and begin cutting several squares or rectangles of colored paper to that size. …
- Add more layers of paper. …
- Make each layer smaller than the last. …
- Allow the glue to dry. …
- Sand the edges. …
- Finish the jewelry.
How do you make a stone out of construction paper?
- Using scissors or a paper punch, cut multiple pieces of construction paper.
- Brush a generous amount of Elmer’s glue between each layer, making sure you go all the way to the edges.
- Let your paper stack dry for at least a day, longer if it is really thick.
How do you make rolled paper bead necklaces?
- Step 1: Tear Out a Colorful Page of a Magazine. See image…
- Step 2: Cut Out a Long Triangle. …
- Step 3: Flip the Triangle Over. …
- Step 4: Put Glue on About an Inch of the Smaller End. …
- Step 5: Roll the Triangle Up. …
- Step 6: Repeat. …
- Step 7: Cut Your String. …
- Step 8: Knot a Clasp to the String.
How do you make paper jewelry waterproof?
Coating origami with clear nail polish is, by far, the most economical waterproofing method for small pieces. You can often find clear nail polish for $1 to $2 in drugstores or discount stores. This technique is used to seal and protect rolled paper beads before stringing them onto necklaces, bracelets, and earrings.
How do you make a paper clip choker?
- Connect a long string of paper clips together and then wrap each paper clip with tape.
- Or, wrap a paper clip with tape and then connect it with another paper clip. Repeat the process of wrapping and connecting until you reach the desired length.
Does Mod Podge make paper waterproof?
As I said before, no, Mod Podge is not waterproof. … Mod Podge is a craft supply made up of several ingredients, including vinyl acetate. The combination produces a product that is somewhat water resistant, but not waterproof. If a few drops of water end up on your Mod Podge project you can wipe them away with ease.
What size strips for a paper chain?
Measurements may vary, but we recommend strips that are 1″ wide by 8″ long. Cut as many as you need, depending on how long you want your chain to be. Paste, tape, or staple the ends of the first strip together to form a loop. If you are using glue, hold the two ends of paper together until the glue properly dries.
How do you make paper garland?
- Cut 1 by 10 in (2.5 by 25.4 cm) strips from 2 pieces of paper. …
- Attach the ends of one strip, then glue them together in a loop. …
- Slide another strip through the first loop, then glue the ends together. …
- Keep adding loops until you run out of strips.
How do you make bracelets with paper beads?
- Step 1: Collect your paper. …
- Step 2: Cut your pages into long triangle strips. …
- Step 3: Flip over triangle so the backside is facing up. …
- Step 4: Glue. …
- Step 5: Repeat with other colors and magazine pages.
- Step 6: To make the bracelet, string the beads onto a piece of string or pipe cleaner.
Article first time published on
How do you make a newspaper necklace?
- Step 1: Take a Newspaper and Roll It to Make a Stick. …
- Step 2: Apply Glue and Roll It Like a Round Pendant. …
- Step 3: Use a Stick and Roll One More Paper and Make a Hallow Stick. …
- Step 4: Cut the Hallow Stick Into Small Pieces. …
- Step 5: Stick All Cut Pieces As Shown in the Picture.
How do you make beads out of cardboard?
One at a time, wrap your pieces of cardboard around a straw. Make sure that the smooth side is facing in and the corrugated (bumpy) side is facing out. The side with the glue needs to be on the inside to hold the bead together. Once the glue dries – usually about 20 seconds – you will have a bead.
How are paper beads measured?
- You need to mark the top part and bottom edges of your paper to your desired size of your beads. …
- I would then take my ruler, to trace the dots and connect them forming a triangular shape. …
- It should look like this.
- You can then cut it into strips by using a craft knife or scissors.
