Remove the ten Phillips head screws from the tailgate panel.Remove the two 13mm bolts from the tailgate panel.Pull off the tailgate panel.Remove the 13mm bolt from the tailgate.Raise the tailgate.Pry off the tailgate handle bezel with a flat blade screwdriver.
How do you take the tailgate handle off a 2008 Silverado bezel?
- Remove the ten Phillips head screws from the tailgate panel.
- Remove the two 13mm bolts from the tailgate panel.
- Pull off the tailgate panel.
- Remove the 13mm bolt from the tailgate.
- Raise the tailgate.
- Pry off the tailgate handle bezel with a flat blade screwdriver.
How do you remove a tailgate handle?
Remove the clips from the tailgate latch rods on each side of the tailgate handle by prying them off with a flat-blade screwdriver. Set the clips aside. Release the tailgate handle assembly from the tailgate by lifting the latch rods from the handle. Lift the handle from the tailgate access hole.
How do you take the tailgate off a 2009 Chevy Silverado?
Pull the passenger’s side of the tailgate hinge straight out(with the tailgate remaining open at a 45-degree angle), then pull the driver’s side out. Hold the tailgate firmly on one side, and have your assistant do the same on the other side. Lift the tailgate up and away from the bed.
How do you open a stuck tailgate on a Silverado?
- Remove the inner tailgate cover or, on newer trucks, remove the tailgate handle trim bezel. The inner cover is held in place by screws. …
- Operate the handle and observe the latch rods in action. Use needle-nose locking pliers to clip onto one of the rods.
How do you open a tailgate with a broken rod?
Grab the screwdriver and move the side of the tailgate where it attaches to the truck side via the hinges. Slide the screwdriver into the hinge mechanism and try to manually release the black rubber gasket that holds the tailgate to the truck hinge rod. Push the screwdriver up to release the tailgate.
How do you remove the tailgate on a 2019 Silverado?
And yes, it IS still possible to remove the tailgate. Just unplug the power and camera connection near the middle of the base of the tailgate, then undo a retaining bolt at the right-side pivot (the motor reacts against this solid mount when raising and lowering the gate). The left side is a free rotating pivot.
How do you change a tailgate handle on a Ford Ranger?
- Step 1: Remove Tailgate Liner and Access Panel Covering the Handle. …
- Step 2: Remove the Two 10mm Nuts Holding the Tailgate Handle in Place and Then Pull Handle Out. …
- Step 3: Before Installing New Handle, Spray Penetrating Oil Onto the Mechanism and Latches on Either Side and Apply White Grease.
How does a tailgate latch work?
A tailgate latch is made up of eight pieces. … The nuts for the handle are easily seen behind the rotating latch assembly. When the handle is lifted, it pushes down on the rotating latch that, in turn, pulls on the rods running to the outside panel latches.
How much is a Chevy tailgate?
There is a wide variety of tailgates for a Chevrolet Silverado 1500, and their prices vary depending on their materials and style. But normally the price of Chevrolet Silverado 1500 tailgates ranges from $200 to $650.
Article first time published on
How do you adjust the tailgate on a Chevy Silverado?
- Loosen both pickup box side hinge bolts (1) on the right and left side.
- Install shims (2) on both sides, if needed.
- Hand-tighten the bolts (1) on each side.
- Close the tailgate and adjust for fit and flushness, both up-down and fore-aft.
- Open the tailgate and tighten the bolts.
Can you open tailgate from inside?
Fold down the seats and open the tailgate from the inside. Most cars have an emergency release on the tailgate. This can usually be operated with a screwdriver. With some models, you can simply remove a small cover in the tailgate and trigger the cable manually.
