In general, the blades on right-handed circular saws turn counterclockwise, so you’d tighten the bolt clockwise; the blades on left-handed circular saws turn clockwise, so you’d tighten the bolt counterclockwise. Hold the outer flange (rim) of the nut with a wrench to keep it from turning.
How do you tighten a circular saw?
In general, the blades on right-handed circular saws turn counterclockwise, so you’d tighten the bolt clockwise; the blades on left-handed circular saws turn clockwise, so you’d tighten the bolt counterclockwise. Hold the outer flange (rim) of the nut with a wrench to keep it from turning.
Can you over tighten a circular saw blade?
Use the blade wrench to tighten the arbor nut until it’s snug; be careful not to over-tighten the nut or it’ll be difficult to loosen it the next time you change the blade.
Where is the arbor lock on a circular saw?
Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there’s no lock button, press the blade into the wooden surface.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. … Other reasons your circular saw blade could be stop spinning are your blade isn’t deep enough, your blade is dull (Very Common), loose clutch bolt, dead battery, power cable issue or motor issue.
What does a spindle lock do on a circular saw?
It’s possible some low-cost circular saws for sale even today don’t have a spindle lock either, but all the ones I’ve got now have that feature. For those who don’t know, the spindle lock allows you to lock the blade in place, so you can take the nut off the spindle and change the blade.
What is spindle lock?
Most cordless drill drivers have a feature called spindle lock. When spindle lock is selected, the motor’s spindle is locked and so the chuck and screwdriver or drill bit cannot turn.
How much does it cost to tighten a circular saw blade?
Insert and tighten the blade bolt until it is finger tight. Lock the blade by depressing the blade lock button. Use the wrench to tighten the bolt the rest of the way, about 1/8th of a turn. Do not over tighten.
Which way does a saw blade spin?
Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down.
How do I know if my blade is tight enough?
Tightening or loosening the blade nut should be fairly easy if you have the right tools. You can determine the tightness by looking at the nut of the arbor and having a feel for it. Turn the nut until it feels tight and then you turn it a fraction more for added security.
Article first time published on
What size blade does a Black and Decker circular saw take?
Black and Decker Circular Saw Blade – 170 x 16 x 40mm.
Why has my circular saw stopped working?
Check that your supply power is not at fault. It could be a damaged power cord or tripped breaker rather than the saw at fault. You can check quickly for that by plugging into another outlet with different cords or breakers to see if the saw then works.
Why does my saw keep getting stuck?
The wood you are sawing is closing the kerf and pinching the blade, Your cut isn’t straight, The set of the saw teeth is not large enough, so the kerf created by the blade isn’t wide enough to allow the saw room to pass without undue friction, or. Your saw teeth are too fine for the wood you’re sawing.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
What is a spindle used for?
a rounded rod, usually of wood, tapering toward each end, used in hand-spinning to twist into thread the fibers drawn from the mass on the distaff, and on which the thread is wound as it is spun.
What is drill spindle?
In machine tools, a spindle is a rotating axis of the machine, which often has a shaft at its heart. … For example, gang drills and many screw machines are multispindle machines. Although a bench lathe has more than one spindle (counting the tailstock), it is not called a multispindle machine; it has one main spindle.
What is the purpose of a spindle lock on a angle grinder?
“Tired of changing complex accessories for your die grinders?”Easy and quick, the spindle lock system enables you to change accessories for your die grinder easily and without a second key.
Why do circular saws cut upwards?
The teeth of circular saw blades are intended to cut upwards into the material from below and this is for safety purposes. It is important that you should not spin them in a different direction just like you spin a table saw blade.
When should I change my circular saw blade?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
Should you ever secure the circular saw to the table to create a table saw?
The greatest danger from making a table saw from a circular saw comes from the lack of safety features. On a makeshift table saw, there’s no place to mount a riving knife or kickback pawls. Rigging up any sort of blade guard is also difficult, and could potentially cause binding, making matters worse instead of better.
Where is the lock on the saw?
Lock pins are typically located on the right side of the hinging mechanism, the side opposite the blade. To lock and unlock the pin, the blade must be in the farthest down position.
Which side should the blade be on a circular saw?
The blade is to the right, with no hands or arms crossing over. The base sits over your workpiece on the left, and when making small cuts, the cut-off falls to the right. With a left-handed saw, a righty’s left hand will cross the blade when gripping the auxiliary handle.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Does a circular saw cut up or down?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering.
What size blade does a Porter Cable circular saw use?
Product Description. The PORTER-CABLE PCC661B 20V Max Lithium Bare 5-1/2″ Circular Saw features a high-performance motor delivers 3000 RPM’s for aggressive cutting. It has a 5-1/2″ carbide tooth blade which delivers a 2-1/8′ cutting capacity for a variety of cutting applications.
How do I stop my table saw blade from wobbling?
If the new blade wobbles, unplug the saw, remove the blade and check the arbor for runout with a dial indicator. Fix the indicator’s base to the saw table and set the plunger perpendicular to and in firm contact with the smooth part of the arbor near the threads.
How tight should a miter saw blade be?
Place the new saw blade on the shaft with the teeth nearest you pointing down, and set the outer blade washer back in place. Using your fingers, insert and begin threading in the blade bolt. Once it’s finger-tight, use the wrench to snug it up the rest of the way, making it good and tight.
