Use a guard that is high enough to cover the part of the blade rising above the stock and wide enough to cover the blade when it is tilted. The blade height should be set so it does not extend more than about 3 mm (1/8 in) above the height of the piece being cut.
How far should a safety guard be above stock on a band saw?
Keep guards in place at all times. The blade guard should be from 1/8 to ¼ inch above stock. Keep hands away from blade and do not open upper or lower bandsaw doors while blade is in motion.
What is the safety margin on the band saw?
Always maintain a 4” margin of safety. If it is necessary to back the saw out of a long cut, turn the power off and wait for the blade to stop.
What should the clearance be between the stock and the upper blade guide assembly?
Upper guide should clear stock by about 6 mm (1/4”). 6.
At what distance should the guide be set on the band saw?
Set the front of the blade guide about one-sixteenth of an inch from the deepest part of the blade gullets (the spaces between the teeth on the blade). What is this? The blade guides must ride behind the teeth on the bandsaw blade.
How high should the blade guard be above the stock being cut?
Use a guard that is high enough to cover the part of the blade rising above the stock and wide enough to cover the blade when it is tilted. The blade height should be set so it does not extend more than about 3 mm (1/8 in) above the height of the piece being cut.
What is the number 1 safety rule of the band saw?
Safety Rules Safety glasses are required. Never clear small pieces while blade is moving. Never adjust saw or setup while saw is running. Never cross arms.
How far from the back of the blade would you position the thrust wheel?
The thrust wheels give support to the blade when cutting. They should be positioned in line and just clear of the back of the blade when the blade is idling after being tensioned and tracked.
How far should the upper blade guard guide be positioned above the work piece?
Make sure the blade is positioned properly on the track. Adjust blade guard height to about 3 mm or 1/8 inch to 6mm or 1/4 inch above the top of the material being cut. Wider gaps will place tension on the blade and increase the risk of breaking.
What should you never cut on a bandsaw?
Always adjust the speed of the band saw while the machine is running. Never adjust the speed with the machine turned off. Never cut materials that might be hardened, such as tool steel, files, hardened guideways, stainless steel etc.
Article first time published on
Does the splitter keeps the saw kerf open?
Your saw’s splitter and anti-kickback pawls are two important components of accurate and safe rip cuts. As its name implies, the splitter keeps the kerf open after the blade makes the cut, preventing pinching that can burn a cut.
Where should a bandsaw blade sit on the wheel?
Make sure the machine is disconnected from the power supply. When tracking, you always want to make sure that the blade is sat on the crown of the wheel, with the deepest part of the gullet in the centre.
What's the minimum distance that your fingers can get to the band saw blade?
10. Keep your fingers away from the cut line and blade. 2 inches minimum.
What is the smallest piece that is safe to cut on a band saw?
1/8-inch blade = 3/16-inch minimum radius cut. 3/16-inch blade = 5/16-inch minimum radius cut. 1/4-inch blade = 5/8-inch minimum radius cut. 3/8-inch blade = 1 1/2 inch minimum radius cut.
Do band saws need guards?
Bandsaws must be guarded. Guarding must prevent access to the bandsaw blade but still allow the employee to see the material being cut. If practicable, employees should use a push stick to guide the work piece through the cutting process. A push stick allows employees to keep fingers and hands clear of the blade.
How high should saw blade be?
The Safest Cut With that in mind, the safest height to set a table saw blade is so it’s just above the wood you are cutting. The general rule of thumb is that the blade should be set so it is 1/8” above the workpiece. If you make contact with the blade with your hand at this height, you’re unlikely to lose a finger.
How high should your table saw be?
When it comes right down to it, the proper height for your table saw depends on your height. While the average height tends to be 34 inches and the standard range is between 31 and 38 inches, the best choice for you will fall right about even with the distance of your thumb knuckle from the floor.
When you are finished using the band saw you should?
When you are finished using the band saw you should: Turn it off and wait for the blade to stop; then use a brush to clean off the table. When operating the band saw, safety glasses do not need to be worn if using a face shield.
What part of a machine should be in position before it is turned on it protects the operator?
Make sure that all machines have start and stop buttons within easy and convenient reach of an operator. Start buttons should be protected so that accidental contact will not start the machine.
When should a blade guard be used?
213 and 1926.304. In general, blade guards are required on table saws whenever ripping or cross-cutting is done. Some OEM guards on cheaper saws don’t work very well due to the fact that they are secured to the saw behind the blade with a thin metal blade called a splitter to help prevent kickback.
Are Anti kickback pawls necessary?
It should go without saying that no one safety device can make a saw 100% safe. While anti-kickback pawls will reduce your risk of injury or equipment damage do not neglect to act carefully and to use other safety equipment.
Is a riving knife necessary?
Because this type of blade does not create a through cut, a riving knife would serve no purpose. In fact, it would actually get in the way, blocking the completion of the cut. … In nearly every other case, though, the riving knife should be used when making standard rip cuts and crosscuts with your table saw.
What kind of stock should not be cut on a band saw without a V block or holding jig?
Don’t cut stock that is not flat on the bottom without a jig. 4. Keep a balanced stance at the band saw. 5.
Why is it best to use a push stick when using a bandsaw?
Push sticks or push blocks should be used when operating standard woodworking machinery, including table saws, band saws, radial arm saws, jointer/planers and shapers. These sticks protect the hand while allowing good hand control of the stock as it is pushed through the cutting head or blade.
Is it safe to back out of a long curved cut while the machine has stopped running?
Never back out of curved cuts while machine is still running as this will result in the blade coming off. (You must wait until blade comes to a complete stop).
Can you cut a 45 degree angle with a bandsaw?
The trick is simple. Stick the magnet to your blade and make sure it’s following the natural angle of the cut, then adjust the backrest on the saw to line up with the 45 degree side.
What saw to make curved cuts?
Circular saw technique When you’re forming gradual curves, you can speed things up by using a circular saw instead. The first tool that comes to mind for cutting curves is a jigsaw, but if the curve is gradual, try a circular saw instead. It’s surprisingly quick and easy to cut a smooth curve with a circular saw.
How should you clear away scraps that are close to the saw blade?
Use a piece of scrap stock to remove scrap pieces; do not use your hands. Keep floor area surrounding the saw clear of scraps. If the blade breaks, stand clear and shut off the power if possible. … Use a push stick or guide for cuts near the saw blade.
When should a splitter be used on a table saw?
The splitter is most effective when it’s sitting as close to the back of the blade as possible, and because the saw’s arbor rotates in an arc, a compromise will have to be made to allow for different blade heights. The easiest solution is to make more than one insert/splitter combo per blade.
Does a splitter prevent kickback?
Riving knives and splitters When it comes to preventing kickback, the best tool for the job is either a riving knife or a splitter. Each of these plates sits aft of the blade and, when properly aligned, as shown in Photo B, keeps the workpiece against the fence to deny it access to the rising rear saw teeth.
Why do bandsaw blades break?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
