x 75 ft. Roll Self-Adhered Roofing Underlayment (225 sq. ft.)
How many squares does a roll of ice and water shield cover?
The length and coverage of a roll of ice and water protector will vary by manufacturer. GoldShield[™] is 66.7 feet long (19.9 meters), and one package has an area of 200 square feet (19.58 meters).
How much ice and water shield do I need on my roof?
Once you calculate how far up the roof needs to be covered, you can calculate the total amount of ice and water barrier needed by multiplying the coverage in feet by the length of the eaves that need to be covered in feet.
How long is a roll of water and ice shield?
Roll length75 ft (22.9 m)36 ft (11.0 m)Roll width36 in (914 mm)36 in (914 mm)Roll size225 ft2 (20.9 m2)108 ft2 (10.4 m2)PackagingCorrugated cartonsCorrugated cartonsRoll weight61.4 lbs (27.9 kg)33.6 lbs (15.3 kg)
How many square feet does Grace Ice and water Shield Cover?
ManufacturerGraceCoverage (Square Feet)200Installation MethodSelf-Adhering; Side Laps must be a minimum of 3.5 inches and End Laps a minimum of 6 inchesInstallation Temperature40 degrees Fahrenheit or higherPackage Quantity1
How much is a roll of ice guard?
This item Grace Ice & Water Shield Roofing Underlayment 36 in. x 75 ft. (225 sq. ft.)Titanium PSU30 Peel & Stick Roof UnderlaymentAdd to CartCustomer Rating4.2 out of 5 stars (20)5.0 out of 5 stars (9)PriceFrom $169.90$15560Sold ByAvailable from these sellersModern Builders Supply, INC
How many feet is a roll of moisture guard?
Part NumberPropertiesUOM826454CoverageArea: 96.75 sq-ft Length: 32 ft 3 in Width: 36 inRL826455CoverageArea: 193.5 sq-ft Length: 64 ft 6 in Width: 36 inRL
Do I need ice guard on my roof?
It’s crucial to have ice and water shield installed on/around certain areas of your roof, like roof valleys, around penetrations, and on roofs that have a 2/12, 3/12, or 4/12 pitch. Because of its importance, every roof needs to have it. There’s also a code if you live in an area above the snow line in the US.
Can you nail through ice and water shield?
When nails penetrate the ice and water shield on the roof, the rubberized nature of the material creates a gasket effect on the shaft of the nail. … Not only does ice and water shield stop leaks caused by ice dams, but it also stops leaks created by fierce wind-driven rain.
Can you use ice and water shield on a flat roof?
Yes, you can use an ice and water shield on flat roofs. It provides two necessary layers of protection for your roof that will absorb small amounts of moisture under the membrane if any water passes through the leak barrier.
Article first time published on
Is drip edge required by code in Wisconsin?
The IRC now requires a drip edge for all asphalt roof installations and provides direction for its proper installation. Underlayment must lap over the drip edge at the eaves.
Is ice and water shield required in Texas?
CODE INTERPRETATION This code implies that ice and water shield—eaves flashing—is required for installation on all heated, steep-slope structures (exception is unheated structures) in colder climates.
Is ice and water shield required in Michigan?
Ice and water shield must be installed from the lowest edges of all roof surfaces to a point at least 24 inches inside of the exterior wall line of the building. More commonly known as felt paper must be installed on all exposed roof decking.
Does Ice and Water Shield go under drip edge?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge. This lets any water that gets on the roof run down the underlayment and over the drip edge.
How many nails should be used per shingle?
General Guidelines for Nailing Shingles Install the recommended number of nails per shingle. For Duration® Series shingles, Owens Corning recommends using either a 4- or 6-nail fastening pattern depending on the roof’s slope and building code requirements. In most cases, 4 nails are adequate.
What kind of plastic do you use in a crawl space?
While thinner plastic or regrind may be okay for short-term use, only reinforced virgin poly should be used for long-term applications like crawlspace vapor barriers. Properly installed virgin reinforced poly should last 20 years or more in a crawlspace.
What is mil plastic under concrete?
Choosing the Right Vapor Barrier The most commonly used vapor barrier under concrete slabs is polyethylene (poly) plastic sheeting with a thickness of 10 mil or 15 mil.
How many linear feet are in a bundle of starter shingles?
Starter Strip shingle is designed to be broken into two pieces, and each piece has its own sealant strip. When separated, each starter shingle is 65 ⁄8″ x 393 ⁄8″, and each bundle will cover approximately 105 lineal feet.
What is high temp ice and water shield?
Ice & Water Shield® HT is formulated with a proprietary adhesive with temperature resistance of up to 260°F. The membrane forms a watertight bond to the roof deck, and seals around fasteners of the primary roof covering and thus maintains the waterproof integrity of the roof deck.
How many bundles of shingles make a square?
How many bundles of shingles per square? A package of roofing shingles is called a bundle. Laminate or architectural shingles, one of the most common types of roofing shingles, are generally packaged in three bundles per square.
Does tar paper go over ice and water shield?
Method 1: Install the ice-barrier membrane according to the manufacturer’s instructions with the drip edge installed on top of the membrane. Then install regular roofing underlayment (tar paper) over the top of the drip edge (and over the ice barrier) and continuing all the way up the roof.
Do I need ice and water shield on a shed?
As ice melts and the water freezes in a continual cycle, the water will creep up the roof and underneath the shingles. This is why it’s important to have Ice and Water Shield because it gives better protection barrier against ice.
Is it bad to ice and water whole roof?
The only real negatives of covering your entire roof with ice & water shield are (1) cost and (2) potential ventilation problems (which are very rare). Ice & water shield acts as a vapor suppressor, so it not only keeps the water out, but also keeps the moisture in.
How do you remove ice and water shield from roof?
Sometimes shingles come off the ice shield better when it is hot. In that case, let the area heat up a bit and then tear that area off, and then the shingles will separate from the ice shield. Sometimes shingles just won’t come up at all.
Is ice and water shield the same as underlayment?
Synthetic underlayment, like an ice and water shield, is quite a bit lighter, rolls out in large rolls, and is made of polypropylene, fiberglass, polyethylene, and polyester. … While they don’t seal the nails as ice and water shield does it is a superior underlayment when compared to traditional felt paper.
Is peel and stick the same as ice and water shield?
In a nutshell, underlayments that offer ice and water shielding are a waterproof membrane designed to protect a roof deck against damage from ice, melting snow and rainwater. … With a peel-and-stick underlayment, the adhesive is designed to seal around nail punctures to keep water out.
Do all roofs need a drip edge?
The 2012 International Building Code (IBC) requires drip edges for that type of roof. Regardless of the kind of roof you have, we highly recommend installing drip edges. Keep in mind that improper installation of any roofing component can create gaps, rendering any waterproofing solution useless.
Do you install drip edge before fascia?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
What is the minimum thickness of roof sheathing?
Sheathing must be a minimum of 19/32-inch thick. Never affix roof sheathing with staples; 8d ring-shank nails need to be used instead. The normal thickness range for sheathing is 3/8 to 3/4 inch.
How do you put ice and water shield on eaves?
Drive nails straight and flush to the surface of the underlayment. Install WaterGuard Rain & Ice first in roof valleys (see instructions below) and as a flashing membrane at roof- to-wall transitions, around vents, curbs, skylights and other roof penetrations; then apply along the eaves.
