What does e11 mean on electrolux washer

The code means the washer took too long to fill. It could be one of three problems, either the machine isn’t filling with water, or won’t fill with enough water or it has a draining issue.

How do you fix an E11 error on an Electrolux washing machine?

Check the water supply to ensure that the water pressure is proper. …
Clean the filter in the inlet hose next to the tap. …
Ensure the correct position of the drain hose. …
Ensure correct drain height. …
Clean the pump and filter. …
Check for blocked drain.

How do you manually drain an Electrolux washing machine?

STEP 1: Turn off the power. Switch the power button on the machine off, if your model has one. …
STEP 2: Locate the drain hose and water supply hoses. …
STEP 3: Drain the washing machine of water. …
STEP 4: Remove a drain hose clog. …
STEP 5: Remove a drain pump clog.

What does E11 mean on my washing machine?

The “E11” error occurs when the washer takes too long to fill with water. After a set amount of time, the washer stops filling and will automatically drain if not enough water has been added.

What does E11 error mean?

However, sometimes even the best machines have error codes and some have received the Electrolux washer code E11 on their machines. … The code means the washer took too long to fill. It could be one of three problems, either the machine isn’t filling with water, or won’t fill with enough water or it has a draining issue.

How do you put an Electrolux washer in diagnostic mode?

Electrolux Diagnostic Mode * Press the Cancel button to enter standby mode and enable diagnostic entry. * Within 10 seconds after pressing Cancel , press any button to wake up the control. button under the display simultaneously for 3 seconds to enter the diagnostic mode.

What is Electrolux smart load sensing?

Thanks to smart load sensing, the washer will determine the perfect amount of water needed to effectively wash your clothing. SmartBoost™ Maximize the cleaning power of detergent through Electrolux’s SmartBoost™ technology.

How do I reset my Electrolux top load washer?

Turn the machine off at the powerpoint, wait for one minute, and then turn it back on. If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds.

How do I unlock my Electrolux washing machine?

On some machines, the door can be opened in an emergency by pulling down on a bar using a screwdriver or similar object, for example. If the machine has an emergency release, it is located next to the fluff filter. See the full description in the user manual. Download user manual.

Is there a reset button on a washing machine?

Most newer washing machines come with a reset feature that allows you to restart the washer after it experiences an error code or fault. … Some machines have a button you push to reset its motor. On a machine without a reset button, unplugging the washer and then plugging it back in often serves as the means to reset it.

Article first time published on

How do I reset my washing machine?

To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I force my Electrolux washer to drain?

Open the pump guard panel.
Pull the emergency hose out.
Place the hose in a container and remove its cap.
Unscrew the pump guard filter.
Wash the filter in the sink to clean it.
With the filter out, check the pump impeller. …
Put the pump guard filter and emergency hose back into the machine.

Why isn't my washer draining?

There are a few possibilities why your washing machine won’t drain. … Your washer may have a clogged drain hose or the pump may be broken. A broken lid switch or belt could also be the culprit. It may even be something as simple as the hose being jammed.

What causes a washing machine not to drain and spin?

If your washer won’t drain or spin, the water level control may be faulty. Open the machine’s control panel and look for a plastic tube attached to the water level valve. If it’s clogged, clear it out with vinegar. If the valve itself is corroded, it may need to be replaced.

What does E10 mean on my Electrolux washing machine?

It indicates problem with not taking in water, not taken in enough water or problems with the drain.

What does e mean on my Electrolux washer?

Electrolux Washing Machine – E – Drain Pump Error – Water Level Does Not Decrease To Reset Point Within 15 Minutes From Draining Water From The Washer. –

What does E12 mean on a Logik washing machine?

Logik Washing Machine Error 12: “E12” Error Code Definition: Washing machine has detected overfill. This error code can be caused by over sudsing from overloading or by adding too much detergent. The pressure sensor will read that there is too much water in the washer.

Does an Electrolux washer have a filter?

In your Electrolux washer model EWFLS70JSS, the tub filter, also known as a coin trap, is found inside the tub to pump hose. The filter prevents foreign objects from entering the drain pump. … A clogged tub filter can also cause an issue with the draining process.

Where is the lint filter on an Electrolux washer?

The coin trap is found inside the tub in your washer model. The drain pump has a filter.

Do all front load washers have a filter?

Clear Drain Pump Filter: Every front-loading machine will have a drain pump filter, typically located near the bottom of the machine. Consult manufacturer instructions for the location, as well as how to access the filter door. Clear this filter after every few washings.

How long does an Electrolux washing machine last?

In general, you can expect brands such as Electrolux (i.e. in the price range of an Electrolux) to last 5-8 years.

How do I find out the cubic feet of my washer?

Measure the depth inside the washer with a measuring tape. …
Measure the diameter of the tub. …
Divide the diameter by two, and square it. …
Multiply the number calculated in Step 3 by the depth of the tub. …
Multiply the number calculated in Step 4 by pi to determine the capacity.

How long should an Electrolux washing machine last?

Electrolux & Frigidaire With both brand names, you know that you are getting quality but does that quality translate into a long life: With Electrolux and Frigidaire, you get 10 years minimum under normal use. This could mean that the washing machine will stop working after 10 years, or it could work forever.

What does E13 mean on Electrolux washer?

Every code means something and this Electrolux washer code E13 means water has leaked and is in the tray. It could be a bad hose, a pressure sensor, a switch, a problem with the mainboard, bad wires that short circuit the appliance, and even a crack in the tub.

Why is my Electrolux washing machine not spinning?

One of the most common reasons a washer won’t spin clothes is an imbalanced wash load. To protect against damage, a spin cycle won’t engage when your machine senses an unbalanced load. If there are too few items in the washer or if it’s overloaded, the load will be unstable, and the spin cycle won’t start.

How do I fix the EHO error on my dryer?

Check the power supply to the appliance. Plug a different product in to the same socket, such as a lamp, this will indicate whether the socket has an issue. …
Attempt to reset the appliance. Remove the plug from the socket, wait 30 seconds and then plug it back into the socket.

How do you force a washing machine to unlock?

Turn the washing machine off and unplug it. If pausing the cycle doesn’t unlock the door, turn the machine off. Then, unplug the machine and wait 5-10 minutes. Try pulling the handle again to see if the door opens. This is the most common solution for top loaders.

How do you manually unlock a front load washer?

Turn off and unplug the washer/dryer.
Close the water faucet.
Wait until the drum has stopped rotating – never open the door while the drum is in motion.
Wait until water and laundry have cooled down when washing with high temperatures.

How do you unlock a front load washer?

You can unlock front-load washing machines within the first 5 minutes of the cycle by pressing the Start / Pause button. Your washing machine will check if it’s safe, and if the water level isn’t too high or the water too hot, it will allow you to open it.

Why won't my washing machine finish its cycle?

A top-load washer won’t advance to the drain and spin cycle if a broken lid switch is making the timer think the washer lid is open. … A washing machine that won’t finish the cycle could also have a broken timer or failed water-level pressure switch.