What is a 33mm socket in standard size

A 33mm metric socket is 1.29921 inches in size which most closely matches a 1 5/16 standard size socket.

What size is a 32mm socket?

Weight0.8 lbsNut End Outside Diameter (B)45.4Socket Length (L)56.4Socket Size32Socket Type12 POINT

What metric and SAE sizes are the same?

While there is no precise correlation between SAE fractional and metric measurements, there are many sockets that are close enough in size to be used interchangeably, in some circumstances. For example, 5/16 and 8 mm, 7/16 and 11 mm, 5/8 and 16 mm, 3/4 and 19 mm, 7/8 and 22 mm, and 15/16 and 24 mm.

What is a 3/8 socket in MM?

SAEMetricInch3/8″0.37510mm0.39413/32″0.40611mm0.433

What is a 30mm socket in standard?

30mm. 1.200. 11/16 Wworth; 3/4 BSF. 1.250.

What are standard socket sizes?

There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters). In-between sizes are available too, starting with 1/4 inch (0.6 centimeters) and increasing every sixteenth of an inch (0.16 centimeters).

Is there a 33mm socket?

Capri Tools Deep Impact Socket, 1/2-Inch Drive, 6-Point, Metric (33 mm)

What are the standard wrench sizes?

Standard Combination Wrenches: 1/4, 5/16, 11/32, 3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1,
Metric Combination Wrenches: 4, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 24, 36, 64,

What is the smallest socket size?

3/8″ Drive1/4″ Drive1/2″ Drive9mm6mm12mm10mm7mm13mm11mm8mm14mm12mm9mm15mm

Is 3/8 and 10mm the same?

It’s the same size. 3/8 is in inch and and its 10mm.

Article first time published on

Is 19mm the same as 3 4?

19mm = 3/4 inch. … 21mm = just over 13/16 inch. 22mm = almost 7/8 inch. 23mm = 29/32 inch.

What is 1/32 of an inch in MM?

Dimensions — Inches to MetricDecimal InchesFractional InchesMetric0.031”1/32”0.79 mm0.062”1/16”1.57 mm0.125”1/8”3.18 mm

How do you tell if a bolt is SAE or metric?

Metric and SAE fasteners are measured differently and with different vocabulary. SAE nuts, bolts and screws are measured by their thread count, or TPI (threads per inch) and their length. Metric fasteners are measured by length and pitch, or the distance between threads.

How do you tell the difference between metric and standard sockets?

SAE sockets are sized in inches and fractions of inches. Metric and SAE wrenches have different systems of measurement. Metric sockets and wrenches use the metric measurement system. This is when millimeters are used to describe the size.

What order do standard sockets go in?

Six Point Standard Sockets (3/8, 7/16, 1/2, 9/16, 5/8, 11/16, 3/4, 13/16, 7/8, 15/16, 1)

What size in inches is 30mm?

Millimeters (mm)Inches (“) (decimal)Inches (“) (fraction)30 mm1.1811 ″1 3/16 ″40 mm1.5784 ″1 37/64 ″50 mm1.9685 ″1 31/32 ″60 mm2.3622 ″2 23/64 ″

What size is 20mm in inches?

MMApproximate Size In InchesExact Size In Inches20mmJust short of 13/16 Inch0.78740 Inches21mmLittle over 13/16 Inch0.82677 Inches22mmJust short of 7/8 Inch0.86614 Inches23mmLittle over 7/8 Inch0.90551 Inches

What is the difference between AF and Whitworth spanners?

AF was introduced much later and refers to Across Flats and was related to UNC(universal national coarse) and UNF(universal national fine) threads in the USA A 1/2 inch Whitworth socket is for a nut that fits on a 1/2 inch diameter thread, and is usually 1.5 times the diameter of the screwed rod across the flats of the …

What is the most common socket size?

½-inch drive size sockets are for high-torque applications like automotive wheel replacement and when you are using a breaker bar. …
⅜-inch drive size sockets are the most common and most available. …
¼-inch drive size sockets are ideal when you are in tight spaces or when you are working with recessed nuts.

How do I know what size socket I have?

Turn on the digital caliper and set it to read in inches, not millimeters. …
Close the caliper jaws until each jaw rests on one flat side of the nut on opposite sides.
Check the caliper display. …
Turn on the digital caliper and set it to read in millimeters, not inches.

How do you read socket sizes?

The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4″, 3/8″, 1/2″, 3/4″ or 1″.
The size of the socket head (the part that fits over or into a fastener).

How many different types of sockets are there?

There are two main types of sockets: impact and hand. Sockets are referred by their number of “points” for the pointed intersections of their multi-faceted interior sides. Common designs include : 6 point, hexagon, for hexagonal nuts.

What is a 28mm socket in standard?

This Metric Standard Length Socket has a 28mm socket size. 3/4″ Drive. 12 Point. 56.4mm Length.

What is the most common bolt size?

The most common were the 12mm and 10mm, followed by the 15, 17 and 19mm.

Is there a 10mm socket?

In fact, the 10mm socket is one of the most commonly used metric size sockets of all. It’s no secret that the majority of parts under the hood and in the car require a 10mm. The applications may vary from car to car, but the 10mm is absolutely vital to complete a project.

What is a 10mm socket in standard?

So what is a 10mm socket equivalent? The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.

Can I use a 3/8 instead of 10mm?

Yes, a 10mm hanger will physically fit on a 3/8″ bolt. 3/8″ = 9.525mm I don’t see any problem with that at all. Just don’t apply that thinking to drill bit diameters and bolt sizes!