The Control Lock button prevents the washer from being accidently started or used by children. This video will demonstrate how to use the Control Lock button.
How do you unlock the control on a Whirlpool washer?
- Locate the “Control Lock/Unlock” button on your Duet’s control panel. …
- Press and hold the “Control Lock/Unlock” button for three seconds.
- Release the “Control Lock/Unlock” button when the control lock icon on the display disappears.
How do I turn off the Control Lock on my Whirlpool washer?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
How do you reset the control board on a Whirlpool washer?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset.
How do I turn off the Control Lock on my Whirlpool dryer?
- Locate the “End of Cycle Signal” button. This is located on the right side of the Duet model dryer.
- Push the button and hold it down for 3 seconds.
- The Control Lock LED should turn off letting you know that your dryer is no longer locked.
How do I reset my Whirlpool Cabrio Top load washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
Do Whirlpool washers have a reset button?
Method 1: Unplug it The first way you can reset whirlpool washer top load is by unplugging it for about 2 minutes then plug it back in and wait about 30 seconds before starting the washer again. This performs a hard reset on the machine and it will start over after you reconnect it again.
What does control lock mean on Whirlpool dryer?
The Loc Error code indicates that the Control Lock has been enabled. When the control is locked, the dryer will not start or operate. Some models will look like the following: Press and hold the Control Lock Key for 3 seconds to unlock the machine. You will notice the machine count down from 3-2-1.
Why does my Whirlpool dryer say control locked?
The dryers have a control lock feature, which prevents children from starting the dryer if they press the buttons on the control panel. … When you are ready to use the dryer, you must unlock the control panel to adjust the settings and start the dry cycle.
How do you manually unlock a Whirlpool Duet washer?
You can manually unlock the washer by removing the top (remove screws on the back of the top panel and slide the top panel back to lift off. then with the washer unplugged reach down and pull a small ring on the top of the door lock to manually open the door lock.
Article first time published on
How do I reset the control panel on my Whirlpool dishwasher?
To reset the dishwasher control panel, it needs to be disconnected from the power source for one minute. If your dishwasher is plugged into an outlet, simply unplug the unit for one minute and then plug the unit back in.
What does the code F11 mean on a Whirlpool washing machine?
The F11 error code in the Whirlpool washer reports about the engine control board malfunction. Communication errors between components in the Whirlpool washer occur quite rarely. … But this appliance is all about water, moisture, and spin at high speed.
Why is my Whirlpool washer door lock flashing?
This means the washer is unable to drain properly, thus it won’t unlock the door. It may also mean you need to replace a faulty drain pump.
What does F5 mean on a Whirlpool washer?
The “F5” error means that the temperature sensor has recorded an unusual reading while using hot water. This usually is a sensor error rather than a malfunction of your hot water heater.
What is the problem with Whirlpool washing machines?
The extra current that runs through the machine when the heating element is on can cause the door locking system to overheat. The company said the issue had been identified by its safety team, but had led to fires, although none had been significant enough to cause more than minor damage or cause any serious injuries.
How do I reset my Whirlpool 6th Sense washing machine?
- Unplug the washer for 1 minute from the electrical outlet.
- Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. …
- The motor has now been reset and is ready for you to start a cycle.
How do I turn off the control lock on my Whirlpool oven?
To turn the control lock setting off, press and hold the START button for 3 seconds. If this doesn’t work, turn the oven off at the circuit breaker for 1 minute. When the circuit breaker is turned back on, the error code should be gone.
What does control lock mean on dishwasher?
The control lock on a dishwasher is intended to “lock” the control from unintended use. It can be used while the dishwasher is operating or not. This is perfect for the household with children who like to touch buttons so the dishwasher cannot be turned on accidently or turned off when running.
How do you unlock the control panel on a Whirlpool oven?
How do you gain access to the controls on an oven? Press and hold on to the lock for 3 seconds to lock the control panel. The light above the lock will turn on. Press and hold LOCK for 3 seconds to open the control panel.
What does control lock mean on Maytag washer?
When the control is locked, the cycles cannot be started or changed. It must be unlocked to operate or run a cycle. The Control Lock can also be set while the machine is running to prevent someone from stopping or changing a cycle.
How do you unlock a Whirlpool front load washer?
- The door may immediately unlock.
- The door lock LED light will blink. The door should unlock after 60 seconds. …
- The washer will go into a hold and drain routine for 8 minutes. After 8 minutes the door will unlock.
How do I test a Whirlpool dishwasher control board?
- Unplug dishwasher or disconnect power.
- Open the dishwasher door.
- Open console and disconnect the keypad ribbon connection from the control (at P1). …
- Put console back together. …
- Plug in dishwasher or reconnect power.
- Wait 5 seconds.
How do I reset my dishwasher controls?
How Do I Reset My Dishwasher Control Panel? Simply unplug your dishwasher. Wait for one minute, then plug it back in again, to reset the dishwasher control panel.
What does f1 mean on a Whirlpool Duet washer?
The F01 error on this model washer means the relay for the drain pump motor on the main control board (CCU) has failed to activate or a communication error between the Central Control Unit (CCU) and the EEPROM onboard the CCU occurred.
What is a F11 error?
The F11 error means the keypad is shorted which is why the control panel has to be replace to fix it.
