OTC’s 5/16″ Battery Terminal Wrench is designed for use on GM side-terminal batteries or any 5/16 inch hex head battery bolt – perfect for the tight spaces often found under modern vehicle hoods. This handy wrench features a 6 pt.
What size wrench fits a side post battery terminal?
The battery terminal cables are held fast around the battery terminals by nuts and bolts. This means you’ll need a crescent wrench, an adjustable wrench, vise pliers or a socket wrench. Select a 10mm (0.4 in) wrench or socket, as most car battery cables have this size nut attached.
What size bolt does a side mount battery take?
Side Terminal Battery Bolt 3/8-16 Thread.
What size nut is on a side post battery?
The Chevy side post battery bolt size is 3/8-16 Thread.
What size nut goes on a marine battery?
Marine battery terminals Marine batteries typically have two posts, a 3/8″-16 threaded post for the positive terminal, and a 5/16″-18 threaded post for the negative terminal.
What size is a battery nut?
Battery Terminal Wrench Most battery terminals are 5/16” or 10mm. Using a specialized rubber-handled wrench will help prevent accidental grounding with other metal parts.
What does a socket wrench look like?
A socket wrench is most commonly a handle with a 90 degree ratchet, along with a set of cylinder shaped “sockets” of various sizes. The sockets fit onto the ratchet by way of a square nub. You can set the ratchet to either tighten or loosen, then keep the socket in place on the nut while you turn the handle.
Can you use a metal wrench on a car battery?
3. Remove the Car Battery Cables. Using a socket or adjustable wrench, loosen the bolts that are holding the car battery cables on to the car battery terminals. … Make sure not to touch the wrench to metal areas, as the metal can ground and cause circuit damage to your vehicle’s electronic system.
What size are battery bolts?
Bolt Measurements We’ll use M8 x 1.25 x 12MM as an example because it is the size used on most RELiON batteries.
What size are motorcycle battery bolts?
Universal M6 BZP battery terminal bolts, suitable for a wide range of motorcycle batteries. Thread size is Course M6 (6mm x 1.0mm) and the total thread length measures approximately 12mm.
Article first time published on
Can you convert a side post battery to a top post?
Remove the side-post terminals. Replace each battery terminal with a post converter. These parts give you a safe and effective way to convert a side design to a top-post configuration. The converters should stretch between the sides and end up along the topside of the battery.
What size is a battery post?
The most common size of battery terminal is 10mm ring. 11mm and 13mm are the sizes of the car battery terminal. The terminal has 13mm for the bolt.
Are all battery terminals the same size?
No, there are various types of terminals. Regular car batteries often have the well known round post type of terminal, however the negative is slightly smaller than the positive post. They don’t really change size for different capacities.
What are the different types of battery terminals?
- The three types are:
- SAE Terminals.
- JIS Terminals.
- L Terminals.
- Marine Battery Terminals.
What is the standard socket wrench size?
There are four common socket sizes: 1/4 inch (0.6 centimeters), 3/8 inch (0.9 centimeters), 1/2 inch (1.3 centimeters) and 3/4 inch (1.9 centimeters).
How do I know what size my socket wrench is?
- The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4″, 3/8″, 1/2″, 3/4″ or 1″.
- The size of the socket head (the part that fits over or into a fastener).
What is the most common size drive socket?
⅜-inch drive size sockets are the most common and most available.
How do you remove a battery post?
Loosen the nut that holds the terminal onto the negative post using a socket wrench. The nut will be located to the left of the terminal. Lift the terminal off the negative battery post. If needed, pry the terminal open with a screwdriver, or gently wiggle the connector until it loosens.
Can you spray wd40 on battery terminals?
Some people use WD-40 to clean their car terminals. This can work well but will require more elbow grease. … Then you’ll spray WD-40 on each of the battery terminals and the cable connections if they’re also covered in grime. Let the WD-40 sit for a minute then rinse with hot water.
How do I loosen my car battery bolts?
Loosen the tie-down nut on a top-post battery, with an open-end wrench. If the wrench spins the square headed bolt on the opposite side of the tie-down, use locking pliers or vice grips to hold down the square head. Remove the battery cables from the battery completely, beginning with the negative cable.
Can I use a wrench on the positive battery terminal?
Use a socket wrench to loosen the nut on the black, or negative, terminal. Most ratchet and socket sets have a socket size that fits the bolt of a battery terminal. Remove the negative terminal from the battery. Repeat the process with the red, or positive, terminal.
Are battery terminals Universal?
Because of it’s malleability, lead battery terminals are universal and the same terminal will work for either the positive or negative battery post.
Which battery post is smaller?
so the Battery Terminal Connectors negative one is smaller than the positive one.
What size is an M8 bolt?
Diameter (d)PitchAcross Flats (s)M50.8mm8mmM61.0mm10mmM71.0mm11mmM81.25mm13mm
Is it OK to just disconnect the negative terminal?
Disconnecting the negative (chassis lead) will protect the electrical side of the battery. Removing the battery and storing it inside will protect the physical battery.
When disconnecting the battery the correct tools to use are?
- Use your socket wrench or adjustable wrench to loosen the nut holding the cable onto the negative battery terminal. …
- Lay the disconnected negative cable carefully to one side, making sure it’s well away from the battery terminal.
Why do you disconnect the negative terminal first?
The reason they say to remove the negative first is because it is safer for you. The negative cable in all modern cars is attached to the chassis of the car. SO when you put your wrench on the negative post to loosen it, and the wrench hits the chassis, nothing happens.
What size are terminal bolts?
Every battery terminal bolt is a 3/8-16 with a 5/16 head.
What size are M6 bolts?
M6 threads are 6mm in diameter, only . 4 mm larger than 12-24 screws. When it comes to racking equipment, 12-24 threads are used with most racks, 10-32 threads are used with Dell equipment, audio rack and M6 metric threads are used with HP equipment.
What size are motorcycle battery terminals?
Motorcycle Battery and Ring Terminals. Fits wires from 2 – 2.5 mm (12-14 AWG). 10mm outside diameter, Hole is 5.4 mm in diameter to fit smaller bike battery bolts.
When did GM start using side post batteries?
First, the division will supply as original equipment on about 80 percent of General Motors car divisions’ 1971 model cars, the new Delco sealed side terminal (ST) battery. This new battery design was introduced by Delco-Remy in 1969, but has been available only in the after-market.
