Choose the most appropriate side of the transom. Since the outboard tiller is usually on the port side of the motor, most kickers are mounted on the starboard-side of the transom to facilitate easier tiller steering and throttle control while slow-trolling or putting home.
How do you stop a kicker motor from bouncing?
Just take the power tilt on the motor and tilt the motor to full up and the motor will not bounce.
Are motor mounts easy to replace?
Replacing engine mounts isn’t too difficult but it can be fiddly. Always check for obstructions between engine and wall (such as crimped AC lines or radiator hoses) before you start. … Raise just far enough to access the engine mounts. Loosen the engine mount bolts using a long extension and universal joint.
Where are the motor mounts located?
You can usually find engine mounts located around the bottom sides of your vehicle’s engine. Some vehicles only have two engine mounts — one on each side — though others have three or four. Regardless, you can usually find them by inspecting the bottom sides of your car’s engines.
How far below the bottom of the boat should the prop be?
If you have a short shaft motor, the top most part of the transom and the lower most part of the boat should be about 15 to 16 inches. For a long shaft, I think 20 to 21 inches is correct.
How do you hook up a main fuel tank to a kicker motor?
one would have the fuel line going to your main motor. You can add a fuel line to the other (basically, screw out the plug, screw in a fuel barb, add a line with fuel bulb then a connector on the other end to connect to the kicker).
Where is the transom bracket?
In boat terminology 101, the transom is the part where the sides of the hull join. It’s part of the stern—the rear end of the boat—and includes the vertical area. The area is ideal for mounting an engine since the spot often has reinforced materials to handle heavy weight and manage the torque.
What is the purpose of a kicker motor?
First and foremost, using a kicker motor helps you save on gas. Trolling with a kicker offers great gas to time ratio, which helps save on the gas you would have been using with your main outboard. Along with gas, they help prevent putting unwanted hours on your main outboard.
What is the purpose of an offshore bracket?
There’s a reason why some manufacturers include these brackets as original equipment on their best center consoles: They work, positioning the outboards and propellers aft of the hull, letting both the props and the hull do their jobs better.
What is a transom saver?
lower unit of your outboard engine to your boat trailer. The transom saver prevents the engine from drifting from side to side and, in general, will keep the engine in place while trailering – particularly when you do not have the clearance to trim your outboard all the way down.
Article first time published on
Can you tighten a loose motor mount?
Thread in the mount bolts, but don’t tighten them. Lower the engine. This makes it easier to align the motor mount. Finish tightening the bolts once you have lowered the engine.
Can motor mounts cause check engine light?
Bad motor mounts shouldn’t cause a check engine light to come on. On the outside chance that do cause the engine light to come on it should set a knock sensor code due to the engine moving/ shifting position and causing a thump that the knock sensor picks up and will adjust timing.
Do motor mounts need to break in?
Re: Break in period on motor mounts? Depending on how much driving you do, they should soften up over the next few weeks. If you still don’t like them after you’ve put 500+ miles on them, then you may never like them.
What size should a kicker motor be?
High Thrust models typically start at 9.9hp which is generally the horsepower size most boaters go with for a kicker. Anything under that size is going to be a standard non-high-thrust model. These motors are just as commonly run as the high thrust models for a kicker.
Where should my cavitation plate be?
The cavitation plate should be nearly even with or slightly below the bottom. For a short shaft the vertical measurement of the transom should be about 15 inches.
How much does it cost to install a motor mount?
For the price of parts, actual motor mounts themselves cost around $50 to $150. The labor to install these mounts and correctly realign your engine costs more than the parts themselves. Expect to spend anywhere from $200 to $450 in labor to replace a motor mount depending on how difficult it is to get to.
Is a kicker motor worth it?
A kicker motor can get your trolling speed slower than main engines. … A kicker motor will burn less gas than your main engine. This is debatable. For starters at idle speed, yes the two cylinder 9.9 motor will burn less than your main power plant does, but that kicker isn’t running at idle when you’re trolling.
Can you put a kicker motor on a pontoon?
The Toon Kicker makes it possible to mount an auxiliary trolling motor on a pontoon boat. … The Toon Kicker can be mounted to port or starboard of the main motor, and a slotted backing plate for the brace makes it possible to fit the unit most boats.
What is a boat kicker plate?
The kicker plate is designed to make it easy to add an additional trolling motor to the rear of your boat that is convenient and dependable.
