Where is the model number on a Hayward pool filter

Luckily, most motor labels come with two searchable model numbers. Hayward labels (pictured) normally have a layout of the Motor Manufacturer model number listed at the upper left and Hayward’s proprietary motor model number normally listed at the bottom left.

Where is the model number on my Hayward pool filter?

Luckily, most motor labels come with two searchable model numbers. Hayward labels (pictured) normally have a layout of the Motor Manufacturer model number listed at the upper left and Hayward’s proprietary motor model number normally listed at the bottom left.

Where is the model number on pool pump?

Pump Model Number – The Pump Model Number is located on the “wet end” aka front housing of the pool pump. This is typically stamped in the pump housing or on a sticker label.

Where is the serial number on Hayward sand filter?

Controls, Electronic Chlorination, ColorLogic Lighting For products such as Aqua Rite, the serial number needed for registration can be found inside the door of the control panel.

Where is the model number on a Hayward Navigator?

Hayward model numbers are found on the data plate or data label on the machine. This is usually located on the back or bottom of the unit.

How long will a pool pump last?

Well-maintained high-quality pool pumps can last between eight to 12 years. If you’ve missed out on many critical pool services, however, you can expect your pump to fail sooner.

Where is the model number on Aqua Rite?

The model number is on the inside of the door.

How do I read my century motor serial number?

The first five numbers of the serial number of most Hayward Century pump motors manufactured since 2006 indicate the date of manufacture, with the first three numbers being the day of the year, and the fourth and fifth numbers are the year.

Where is serial number on Hayward pool heater?

The Hayward HP21404T HeatPro 140,000 BTU In Ground Pool Heater has a data plate which is located on the perimeter of the base pan which includes the model number, serial number, and operating specifications. 1 of 1 found this helpful. Do you? It is on a tag on the lower left hand side of the heat pump.

What does up rated pool pump mean?

Once you have understood the system, you will realize that a pump that has a higher horsepower listing and a lower service factor listing is described as an up-rated motor. The original motor is called a full-rated motor. The pumps are basically the same; they simply have different horsepower and service numbers.

Article first time published on

Where is the serial number on pool liner?

Help Finding Serial Number. The Serial # for your Inground Liner can be found in several places; the back of the liner at the top of the wall seam next to “deep sticker”, on the box the liner came in and at the top of your warranty card.

What is the warranty on a Hayward Salt Cell?

Hayward AquaRite 40K Gallon X-Life Salt Cell 4 Year Warranty.

What size filter do I need for a 15000 gallon pool?

For instance, a 16” sand filtered system has a 1.55″ sq. ft filtered area, making it ideal for a 15,000- gallon pool.

How do I figure out what size pool filter I need?

Filter Size to Pool Size The formula is Length x Width x Average Depth x 7.5, for rectangular pools. For oval pools, change the multiplier from 7.5 to 5.9.

How many sq ft is my pool filter?

For circular pools, multiply the diameter times the diameter times the average depth times 5.9. For oval pools, multiply the long diameter times the short diameter times the average depth times 5.9. For rectangular pools, multiply the length times the width times the average depth time 7.5.

How do I reset my Aqua Rite 900?

To reset, move the switch to ‘Off’ and then back to ‘Auto’. Wait for the relay to click (5 to 10 seconds). When the instant salt level is stable (and the negative sign still present), slide switch to ‘Super Chlorinate’ and back to ‘Auto’. It takes about 30 seconds for the unit to settle back on the default reading.

How do I change cell type in aqua rite?

Slide the Main Switch to the “Auto” position.
Push the Diagnostic button repeatedly until “t-xx” appears on the display (“t-15” is. the factory default). …
To change to a different cell type, slide the Main Switch from “Auto” to “Super. …
Push the Diagnostic button to exit.

How long do Hayward pumps last?

How long do pool pumps last? Your pool pump should be replaced anywhere between 8 to 15 years depending on the quality, and a full replacement may cost over $800. Your pool pump is the “heart” of your swimming pool as it circulates water throughout, bringing water through the filtration and heating systems.

How long is a Hayward pool pump warranty?

All products manufactured by Hayward Flow Control are warranted against defects in material or workmanship for a period of three years from date of shipment. Our sole obligation under this warranty is to repair or replace, at our option, any product or any part or parts thereof found to be defective.

How long should a Hayward pool pump motor last?

Your pool’s pump is the wet end of the operation, it houses the pump basket. Pumps should last through the initially installed motor and perhaps as many as two or three replacement motors, usually 10-12 years.

How old is my pool heater?

Look for the dash at the end of the first series of letter/number digits. It will be followed by a single letter and two numbers. The two numbers are the year of manufacture, and the letter is the month in an A = January, B = February, and so forth, format. Here’s an older stamped metal one above.

Where do I find my Pentair model number?

ON THE BACK OF THE CLEANER, ON THE BASE OF THE HANDLE. LOCATED UNDER HANDLE.

How do you read a Hayward serial number?

First Digit = Standard Warranty length. 4 = 4 Year Warranty. …
Second Character = Product Family. …
Third & Fourth Digit indicate the year the product was made. …
Fifth – seventh digit = day of year manufactured. …
Digits 8 and on = 123456 = Manufacturing ID.

How old is my Hayward pump?

How do I determine the age of a Hayward pool heater from the serial number? The 5th and 6th digits of the serial number of a Hayward heat pump pool heater are the year of manufacture, and the next two are the month.

What is the warranty on a century pool motor?

All Century® motors are warranted against defects in materials and workmanship for a period of twelve (12) months from the date of installation or twenty-four months (24) from the date of manufacture, whichever comes first except for E-Plus®3 Integral Horsepower Motors and HeatMaster® Condenser Fan Motors which are …

How do you remove a Hayward pool filter?

For a cartridge filter, simply depress the latches on the top of the filter tank. For DE and sand filters, use a wrench to loosen and remove the bolts securing the lid in place. All Hayward filters are equipped with a locking ring. Use a screwdriver to unscrew the locking ring.

How do I remove the cartridge from my pool filter?

Turn off the power to your pool pump. …
Open the valves on the filter. …
Remove the lid from the tank. …
Remove the cartridge from the filter canister. …
Set it down in a good spot for cleaning. …
Inspect the cartridge for damage. …
Hose off the cartridge.

What does HP mean on a pool pump?

2. HP – HORSEPOWER. This value refers to the amount of work capable by the motor. All motors spin at the same speed, 3450 RPM, but the higher the horsepower, the greater the volume of water that will be pumped.

What does SF mean on a pool pump?

Horsepower (HP) x Service Factor (SF) = Total Horsepower (THP) The following examples were taken from a few common pool pump motors and will help to better illustrate this formula.

What is the difference between a pool pump and a pool motor?

The pump’s shaft spins up to 3,450 revolutions per minute to turn the impeller to draw water from your pool and then push it through your filter and back to the pool. The motor is a cylindrical steel enclosure, usually black but sometimes gold or almond-colored, bolted to the back end of the wet end.