Loc: Whirlpool oven error code “loc” indicates that the control lock setting is activated. This setting deactivates all oven controls and locks the door. To turn the control lock setting off, press and hold the START button for 3 seconds. If this doesn’t work, turn the oven off at the circuit breaker for 1 minute.
How do I clear the LOC on my Whirlpool oven?
Press and hold START for 5 seconds. A single tone will sound, and “Loc” will appear on the display. Repeat to unlock. “Loc” will disappear from the display.
How do I reset my Whirlpool oven?
- Power unit down by turning off the circuit breaker(s) for one (1) minute.
- Power unit up by turning on the circuit breaker(s).
- Start a bake cycle.
- Monitor the oven for one (1) minute to ensure the error code does not display again.
- Verify oven operation.
How do you unlock a Whirlpool oven?
How do you gain access to the controls on an oven? Press and hold on to the lock for 3 seconds to lock the control panel. The light above the lock will turn on. Press and hold LOCK for 3 seconds to open the control panel.
Why is there a lock on my oven?
Oven locks are a mechanical feature that allows you to secure your oven door. Typically the oven lock only really needs to be engaged if you don’t want young ones opening the door while the appliance is on or when the self-clean function is running to keep everyone safe from the extreme heat.
How do I reset my oven?
Turn the circuit breaker to the OFF position or remove the fuse. Wait one minute, then turn the circuit breaker back to the ON position or install the fuse to reset power to the unit. This should reset the electronic controls on the range or wall oven.
Is there a reset button on a Whirlpool oven?
Press the “Off/Clear’ button for three seconds to turn the “Control Locked” child lock off. Reset the cooking program if “Off/Clear” was pressed accidentally. For example, press the “Defrost” button again, and turn the dial to select the defrost time you want again. Press “Start.”
Why is my oven door not closing properly?
If your oven door doesn’t close all the way or hangs unevenly, several issues could be the culprit. … Replace the hinges with identical new ones and hook them back into the hinge holes in the oven. Push the door down to lock the hinges in place, or replace the screws. Check the door springs to see if they are broken.
How do I reset my Whirlpool oven after a power cut?
Look for “Control Lock” on the oven control console and then reset by typically holding the button(s) for 3 seconds.
How do I turn off the control lock on my stove?
After connecting the appliance to an electrical power supply or after a power failure, the control panel will be locked. An indicator light above the key icon will be on. To unlock the control panel, press and hold CONTROL LOCK for 3 seconds. The indicator light will turn off, and the appliance is ready for use.
Article first time published on
How do you unlock the Control key?
You can also try holding down ctrl+shift for 15 secs. This will release the modifier key lock. This happens when you hold down the ctrl key down for few seconds (happens a lot on laptop where the ctrl key is conveniently located right where you would rest your palms when typing.)
How do I get the control lock off my Kitchenaid oven?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
Why is my Whirlpool oven not working?
If an oven won’t turn on there could be an incoming power problem. … One of the wires that supply power to the oven element or igniter might be burnt out. These wires commonly burn out near the heat source. To determine if a wire has burned out, inspect the wires leading to the element or igniter.
Where are the fuses on my Whirlpool oven?
The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place.
Why is my stove working but not my oven?
In most common cases, this specific issue means that the broil element and the baking element remain functional. However, there’s probably a blown internal fuse. If it’s not the fuse, it could be the temperature sensor, broken or frayed wiring, or even a breakdown of the oven control board.
How do you unlock a Whirlpool oven without power?
- Press Cancel/Off key to start a latch reset, wait 20-30 seconds and open door.
- Turn the power off at the circuit breaker or fuse box for one minute, then turn the power back on.
How do you turn on a Whirlpool electric oven?
To preheat a Whirlpool oven, begin by pressing the Bake function. The oven will automatically display a temperature of 350 degrees Fahrenheit (175 degrees Celsius). If you need to bake at a higher or lower temperature, use the arrows to adjust. Then press Start.
Will electric oven turn back on after power outage?
If the electric oven is controlled by a digital timer or digital controls then it’s unlikely that it will turn back on after a power outage. However analog timers and manual controls will probably remain in the ON position and will restore power to the oven when power is restored.
How do I unlock my touch stove?
Be sure nothing is sitting on cooktop surface. If surface is wet, dry surface and retry. To unlock it, hold the key symbol for 5 seconds, and the unit will beep twice. The key light will disappear, unlocking the unit.
What is control lockout on an electric range?
The Gas/Control Lockout feature disables the cooktop, locking out the control so that pressing the pads does not activate the controls. Gas flow is stopped to both the cooktop and the oven.
What does loc mean on a gas stove?
LOC means the control panel is locked. Per the Use and Care Guide: 1. Check that the oven and cooktop are off. 2. Press and hold CONTROL LOCK for 3 seconds.
How do I turn off the control lock on my GE Profile stove?
Unlock a GE Oven Control Panel The lockout setting is activated by pushing and holding the “lock controls” button for three seconds. Deactivating the lockout is also accomplished by holding down the “lock controls” button for three seconds.
Why is my control button stuck?
Recovery: Most of the time, Ctrl + Alt + Del re-sets key status to normal if this is happening. … Another method: You can also press stuck key: so if you clearly see that it is Ctrl which got stuck, press and release both left and right Ctrl .
Why is my control key not working?
Reasons for Control Key Not Working The possible reasons include: There is a physical problem with the Ctrl button. There is a bad Windows update. The HID driver is corrupted or improper.
How do I turn off the control lock on my Whirlpool washer?
Press the button for that dedicated key to activate and deactivate the Control Lock. To turn off Control Lock, press and hold the Options key that says “Control Lock Hold 3 Sec” under it for 3 seconds.
