If your chainsaw blade will not rotate, the chain may be tensioned too tight. … If the chain is too tight, the blade may not spin when the throttle is engaged, which can cause damage to the clutch or other associated parts. Keep in mind that the tension of the chain will change with heat.
How tight does a chainsaw chain need to be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why is my Poulan chainsaw flooding?
Does your chainsaw fail to start and you don’t know why? There could be various causes: incorrect fuel mixture, carburation not calibrated properly, or a wet spark plug. Neglecting to look after a chainsaw can lead to malfunctions such as flooding. …
How do you tighten the chain on a 2000 Poulan chainsaw?
Adjusting Tension Raise the tip of the bar and turn the adjustment screw clockwise until the section of chain along the bottom of the bar does not sag. Test tension again by lifting the top of the chain. Tighten the bar clamp nut and perform a final check of the tension.
Does Poulan make a good chainsaw?
Poulan is one of the most respected chainsaw brands – it’s right up there with the likes of ECHO and Jonsered. Poulan saws cost about the same when comparing apples for apples as well (or ccs for ccs). This 50cc Poulan Pro chainsaw is not quite on the same level as Stihl or Husqvarna, but it is significantly cheaper!
Does Poulan make a 14 inch chainsaw?
The Poulan 14-inch, 33 cc gas chain saw is perfect for light cutting jobs around the yard, with a cutting capacity of 28 inches diameter. The auto-oiling system keeps the 14-inch steel bar and chain fully lubricated. … The chain saw features a primer bulb for an easy start.
What is the oil to gas ratio for a Poulan chainsaw?
A: Mix 3.2 ounces of Poulan 2-cycle air cooled engine oil to one gallon of fresh unleaded gasoline to obtain the recommended 40:1 fuel to oil ratio. Over a period of time oil will separate from gasoline.
How do I know what size my chainsaw chain is?
The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be. If you do not know your chainsaw pitch you can gauge it by measuring the distance between three rivets.
What size chain goes on a Poulan PL3314?
Powered by a 33cc 2-cycle gas engine, the PL3314 is equipped with a 14 in. steel bar and chain. Lightweight and perfect for cutting firewood and tree limbs around the house.
What size chain do I need?
After a measurement is obtained, its a good idea to opt for a necklace size that is at least the second size up from your neck size. For example, if you have an 18 inch neck, you should probably choose a chain length of 20 inches or more. An 18 inch chain would feel too tight.
Article first time published on
Can you change bar length on chainsaw?
Yes, but you need a bar designed to fit on your saw. There are different designs for different saws, and the bar has to match the chain/sprocket configuration as well.
How do I know if my clutch is bad on my chainsaw?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Can you fix a broken chainsaw chain?
If you have decided to repair the chain, at this point you can do so. You can sharpen the chain with a chain sharpener, remove additional chains using the rivet punch or screwdriver if the chain has stretched, adjust the links in the chain, or replace damaged links in the chainsaw chain.
Where is the chain brake on a chainsaw?
The chain brake is activated when the front hand guard, located near the saw’s upper handle, moves rapidly toward the chainsaw operator. When engaged, the chain brake stops the chain from rotating around the saw’s guide bar.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Do Electric chainsaws overheat?
Electric chainsaws tend to overheat when used extensively, or when they are not assembled properly. This could be due to a loose part that missed while assembling the saw or a lack of lubrication that creates heat due to friction between parts.
How often do you need to sharpen a chainsaw?
You can mount your sharpener if you use your chainsaw throughout the year as it makes it easy to sharpen the tool and also helps to avoid accidents. In most cases, sharpening the chain should happen after ten times of being in use, while in other situations, you have to sharpen it after every session.
