While a chain saw does produce some heat while in use, it should never overheat or begin smoking. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.
What does it mean when your chainsaw smokes?
While a chain saw does produce some heat while in use, it should never overheat or begin smoking. … The most likely causes of smoking and overheating are a lack of air and/or a lack of lubrication to the engine or the chain saw chain guide bar.
Why is my Husqvarna chainsaw overheating?
Chainsaw engines run at high temperatures, usually in the summer, so they can quickly overheat. … If dust, wood chips or other material blocks these systems, the engine will start to overheat. The engine also needs to expel hot air, so the muffler must also be kept clean to keep the engine from overheating.
What causes white smoke from a chainsaw?
The main reason for a chainsaw that emits smoke (white most of the time), is the result of a bad oil / fuel mixture or bad oil. … Be careful, white smoke from bad mixing will cause further breakdowns and damage the entire mechanism.
Why is my chainsaw burning the wood?
If the oil pump for the bar oil is not pumping oil on to the bar it will cause the chain and the bar to get very hot. If this is happening, it may cause the wood to burn. The only other thing I can come up with is the chain may be very dull or on backwards.
Why does my chainsaw chain dull so quickly?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Why is my chainsaw bar overheating?
Overheating Chainsaw Blade The two most common causes of the overheating or smoking of your blade are lack of lubrication of the bar guide or the engine and lack of air.
Will burnt wood dull a chainsaw?
Cutting burned trees is extremely demanding on a chain saw. It is very abrasive and fine particles. Check the air filter often. It will need cleaning or replacing on a regular basis.
How tight should your chainsaw chain be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
When should you throw away a chainsaw chain?
Chainsaw feels unbalanced, cuts unevenly, or rattles when in use. In short, if you have attempted to balance your cutting teeth, are certain of your depth gauge, and the tension is properly adjusted, but the saw still doesn’t cut correctly- then you need to replace the chain.
Article first time published on
How often should you replace your chainsaw chain?
When you own a chainsaw and see that it does not cut as well anymore you will have to decide whether to replace it or sharpen the chain. A chainsaw chain could serve you for more than five years if it is occasionally used, and still help you accomplish most of your tasks.
Can you over tighten a chainsaw chain?
After a few hours of use, a chainsaw’s chain can loosen and begin to sag away from the bar. … There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why is my chainsaw smoking and not cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Does wet wood dull a chainsaw?
Does Cutting Wet Wood Dull a Chainsaw? Using your chainsaw to cut through wet wood will not dull the chain any faster than using it for other types of wood.
How many times can a chainsaw chain be sharpened?
To keep your saw cutting in a straight line, be a fanatic about filing each cutter with the same number of strokes and the same amount of pressure. Cutters can be sharpened up to 10 times or more before the chain needs replacing.
What is bar oil for chainsaws?
Petroleum-based bar oil has been the standard for chainsaws. Lightweight oil is used in winter and heavier oil in summer. Manufacturers of chainsaws make bar and chain oils specially blended for their machines to extend their lifespan, but if they are not available, the owner’s manual suggests alternatives.
How long should a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
How often should I flip my chainsaw bar?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Why does my chainsaw always cut to the right?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
How much does it cost to mill a log?
The most stable or secure method for pricing for the mill owner is a flat, hourly rate. Rates vary from location to location and range from $65 to $105 per hour plus extra charges for travel, broken blades, etc. Pricing on an hourly basis transfers all of the risk of daily output to the customer.
Why is my chainsaw bar sparking?
The tension not being right is perhaps the most common reason a chainsaw sparks. If the tension is not right, it means that there is too much free moving space between the bar and the chain. When you are running it, the two will collide, and you will notice the sparks spontaneously.
Can you cut a tree after it rains?
Unfortunately, storms, high winds, and even light rain usually means the tree removal process will have to be rescheduled. … A person cannot do that safely in stormy, windy, or rainy conditions. That means the best weather for the tree removal process is a sunny or overcast calm day.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
What happens if you run a chainsaw without bar oil?
No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
How do I know if my chainsaw blade is dull?
Smoke crops up even though the chain lubrication is in working order and the chain tension is correct. The chainsaw runs in one direction causing a crooked cut. This is an indication of dull cutting teeth on one side of the chain or uneven cutting teeth lengths. The chainsaw “rattles” and “bounces” during the cut.
How much does it cost to sharpen chainsaw chain?
HOW MUCH DOES IT COST FOR YOU TO SHARPEN MY CHAIN PROFESSIONALLY? If you bring the chain into our shop off your saw, our average chain sharpening price ranges from $13- $16.00, depending on the number of cutters.
What kind of oil do you put in a Husqvarna chainsaw?
Husqvarna X-Guard Premium Bar and Chain Oil has been designed to provide ultimate protection to cutting equipment while operating a chainsaw. Formulated from virgin base stock oils, Husqvarna’s X-Guard lubricant reduces friction and wear on cutting bars and chains, extending the life of cutting equipment.
